seems as though you're encountering trouble while sewing little plans like stones, where the development becomes more diligently and afterward stalls out. This could be because of different factors, for example, needle issues, string strain, or machine support. Checking these angles could assist with further developing the sewing system.
Question edited for clarity. A DB2 is a car made by Aston Martin, but this appears to be a sewing machine. All question need 'make model (what it is)' as first 3 words please.
Question moved from Computers category to Brother Sewing.
This is the only resource I can find for Brother Error 03
E03Cause
This message is displayed when the buttonhole lever is up, a buttonhole stitch is selected, and a button, such as the "Start/Stop" button, is pressed.
Solution
Lower the buttonhole lever before continuing the operation.
https://www.google.com/search?q=Brother+DB2-B755-3A+mark+111+error+code+03
..
Lois, all questions need full 'make model (what it is) please. Futura is a range of models so ''Singer Futura' isn't specific enough. Add the model number after the word 'Futura' and press enter.. You can also look for the Service Manual. There is one in the link, but no Error 20.
https://www.google.com/search?q=Singer+Futura+Error+20
..
I assume the switch you are talking about is the one on the front bottom of the machine. this switch should not slide back and forth easily, if it does than the linkage has been disconnected or broken. To check this you need to open the bottom of the machine and see what happens when you move the switch. To open the bottom you will need a torx screwdriver. First remove 4 long screws that go through bottom and into back, than remove two shorter screws that go through bottom into front cover, next remove 3 short bolts that hold the bottom to frame. If you can't see anything broken or loose after opening the bottom, you might need to remove the covers.
If the handwheel on your Huskylock machine won't turn and the needles won't go down, there may be several issues. Check for thread jams, tangled threads, or broken needles in the bobbin area. Ensure that the machine is properly threaded, the presser foot is down, and the stitch length is not set to zero. If the problem persists, it could be a mechanical issue or a need for lubrication. Consult the machine's manual for troubleshooting tips or contact the manufacturer's customer support. If you're not comfortable addressing the problem, seek assistance from a qualified technician or service center. click
If you're encountering a "Presser Foot Too High" error despite the foot being down, check for potential issues. Ensure the machine is threaded correctly, the needle is not bent, and the presser foot is securely attached. Verify if there's any fabric or thread caught in the mechanism. Additionally, consult the machine's manual for troubleshooting steps or contact the manufacturer's customer support. If the problem persists, it might indicate a mechanical issue that requires professional inspection. In some cases, recalibrating the machine or updating its software may resolve the error. Always follow safety guidelines and turn off the machine before attempting any adjustments. click
To use the White Mighty Mender W100 Mini Sewing Machine, follow these steps:
1. Place the machine on a flat, stable surface. 2. Plug in the machine and turn it on. 3. Thread the machine by following the threading guide provided in the manual. Make sure to use the correct thread and needle for your project. 4. Place your fabric under the presser foot and lower the foot to hold the fabric in place. 5. Use the handwheel to lower the needle into the fabric at the starting point. 6. Press the foot pedal or use the start button to begin sewing. 7. Guide the fabric through the machine while sewing, keeping a steady pace. 8. When you reach the end of your seam, use the reverse lever (if available) to backstitch and secure the stitches. 9. Lift the presser foot and trim the thread.
For more detailed instructions, refer to the user manual that came with your Mighty Mender W100 Mini Sewing Machine. If you don't have the manual, you may be able to find one online by searching for "White Mighty Mender W100 manual" or contacting the manufacturer directly.
try changing the needlerethread the machine top & bobbinclean under the needle plate & in the bobbin area for loose threads or lintcheck to make sure the bobbin & bobbin case is not damaged
Question edited for a lot more clarity. FULL 'make model (what it is)'.
Question moved to model category.
Videos down below or take in for its yearly service, clean, lubrication and timing.
..
Clean all the fluff and lint with a 1" paintbrush. Clean any gummy oil deposits with spirits. Apply one drop of sewing machine oil to every part that slides and every pivot that has a hole in the joint.
Not much on that machine
https://www.google.com/search?q=Homestyles+model+F08-702-H-01+sewing+machineAround the bobbin case: Put one drop of oil around the metal/metal spool case and under the machine if access can be gained. The main bottom shaft will have two bush bearings requiring oil as well as may be the gears and excentric feed cams. Keep oil away from any belts whilst working under the machine.
Dec 13, 2023
It sounds like it needs cleaning and servicing, and perhaps new blades. They should be serviced every year if you use it a lot.
Why is my overlocker not cutting?
If the fabric is not cut properly by the overlock machine, or the machine pulls the fabric into the machine, the blades are probably dull or damaged. When you use your locker a lot, the knives become dull, especially when using thick and special fabrics.
DON'T cut lumps out of your machine. There will be a sequence you use to remove the parts you need to access to the gears more easily. The Youtuber you referred to sounds like they have zero knowledge when it comes to these older style machines.
'Note' Some of the gear mount nuts are on a "Reverse" thread meaning you turn them the 'wrong' way to get them off.
My limited knowledge is more on the much older hand crank and treadle machines.
Try the Youtube link below for a channel called 'Andy Tube'. He has a good reputation for correct repair methods. The link is for a 758 but they're both Touch and Sew machines.
You could also try the Facebook group 'Vintage Singer Sewing Machines' as they have loads of knowledge about loads of different machines.
https://www.youtube.com/watch?v=zxd5hKjGBlE
If the one and only problem is that the wheel is very stiff, doesn't that suggest some fluff, or what, is blocking the wheel?
Are there any other symptoms?
