Science & Laboratory - Page 7 - Answered Questions & Fixed Issues
BSA 3-12 x 50 Rifle Scope
But a new scope. Having the crosshair reseated will cost you more than getting a new BSA scope.
4/3/2018 1:49:24 AM •
Science &...
•
Answered
on Apr 03, 2018
•
702 views
Can't open main door after a spin J6B
Disconnect the main power. Wait 5 minutes and then reconnect power. Door lock will release. If this doesn't work, the locking relay needs replacement.
4/3/2018 1:22:32 AM •
Beckman J6B
•
Answered
on Apr 03, 2018
•
734 views
Which Is The Best Laboratory Chain For Conducting Tests And Analyses?
Choosing the right laboratory for conducting various tests and analyses can be a tricky affair. If there is any discrepancy in readings, it can be cause quote a stir. Thus, it is imperative that the staff operating the equipment of the laboratory must be expertly trained. The equipment itself must be top notch in quality. LiveScanLabs has managed to meet all this criteria. They have centers in
Hialeah,
Hollywood,
Fort Lauderdale,
Pembroke Park and
Pembroke Pines. They conduct
Fingerprint Analysis,
Fingerprint Testing,
**** Analysis,
**** Testing,
DNA Analysis,
DNA Testing and regular health tests as well. Visit their website at
www.livescanlabs.com.
3/3/2018 10:36:45 AM •
Science &...
•
Answered
on Mar 03, 2018
•
603 views
Seems like solvent A and B are confused
By convention solvent A is the aqueous solvent and solvent B is the organic one, so the designation seems to be right. The baseline does not always raise with the increasing amount of solvent B, it depends how steep is the gradient.
Error 102 microscope not plugged in
One has to have a compatible operating system with the correct driver, Your computer operating system must be set for reading the USB port as a video device, f you are able to read any data from the scope you should also check firmware version against the manufacturer's latest revision. Also suggest you download the operator's manual from the manufacturer's site.
Just aquired an old olympus
Olympus makes good microscopes so you have done well and stereo microscopes are so much nicer to use than singles. As far as cleaning the lenses goes, buy a good quality camera lens blower brush and also a can of compressed air like the ones used for computers. Blow any loose dust hairs etc off with the can of air and then use the brush for anything remaining. If there are fingerprints or grease on the lenses then clean them using camera lens cleaning fluid and lens tissue but make sure all debris and dust are removed first or you may scratch the lenses. In general try not to use anything more than air and a brush unless absolutely necessary. Another option for removing fingerprints etc is to use a "lens pen" with caution. The ones sold for cameras work well but may be too large. They make some smaller ones for cleaning camera sensors and those might work better for the relatively small microscope lenses or just cut the regular lens pen disk to make it smaller. It is just as important to make sure the lens is dust/debris free when using the lens pens.
Low power stereo microscopes often allow you to put on a single magnifier lens in front of the main objectives to increase magnification. Do a bit of searching to find what are options for your model.
Heraeus pico biofuge
Are you sure that the lid safety interlock switch isn't damaged/dirty? If the centrifuge can't detect that the lid is closed it will never start. Sometime it just needs an extra push down on the lid.
1/17/2018 7:28:09 PM •
Science &...
•
Answered
on Jan 17, 2018
•
1,734 views
Premiere MS01u microscope bulb flickers. Won't come on.
It sounds like either the bulb is loose or the connection between the bulb socket and a wire is loose. To check both, Loosen the screw knob on the underside of microscope and open the panel to expose the bulb. Use a small screwdriver to loosen the screws holding (the two screws closest to the bulb) the prongs of the halogen bulb. Note that the prongs of the bulb are held in place by small brass plates which shift slightly when the screws are loosened. Remove the old bulb. Important: Do not touch the new halogen bulb with bare hands. Wear gloves or hold the bulb using tissue or lens paper. Body oils may damage the halogen bulb. Insert prongs of replacement bulb into top of socket (above the brass plate) and tighten screws slightly. (The brass plates will move up to hold the prongs in place.) Close door and hand tighten the thumbscrew knob.
If this does not work, contact Premier for assistance: Premiere® Microscope Service, 7241 Gabe Court, Manassas, VA 20109 (703) 330-1413
1/15/2018 6:35:24 AM •
Science &...
•
Answered
on Jan 15, 2018
•
929 views
Hello,
does anyone recognize E61 error code for Euronda E9 autoclave please?
The error E61 indicates that your water pump has failed or is not active. You should check the pump and replace it if needed. You should also check the steam generator sensor and replace it if needed.
For more information, contact Euronda at Water inlet pump inactive or call (+39) 0445 329811 (Vicenza, Italy)
1/15/2018 6:14:50 AM •
Science &...
•
Answered
on Jan 15, 2018
•
973 views
MS-01U Parts
If this is a microscope, the part you are referring to is the stage control. You can get the part from C&A Scientific at http://www.cnascientific.com or by calling 703.330.1413
1/15/2018 6:02:43 AM •
Science &...
•
Answered
on Jan 15, 2018
•
599 views
Not finding what you are looking for?