Science & Laboratory - Page 4 - Popular Questions, Answers, Tips & Manuals
BSA 3-12 x 50 Rifle Scope
But a new scope. Having the crosshair reseated will cost you more than getting a new BSA scope.
2/16/2018 5:09:02 AM •
Science &...
•
702 views • 0 helpful votes
Hello,
does anyone recognize E61 error code for Euronda E9 autoclave please?
The error E61 indicates that your water pump has failed or is not active. You should check the pump and replace it if needed. You should also check the steam generator sensor and replace it if needed.
For more information, contact Euronda at Water inlet pump inactive or call (+39) 0445 329811 (Vicenza, Italy)
1/8/2018 11:10:11 AM •
Science &...
•
973 views • 0 helpful votes
MS-01U Parts
If this is a microscope, the part you are referring to is the stage control. You can get the part from C&A Scientific at http://www.cnascientific.com or by calling 703.330.1413
1/11/2018 10:06:03 PM •
Science &...
•
599 views • 0 helpful votes
Premiere MS01u microscope bulb flickers. Won't come on.
It sounds like either the bulb is loose or the connection between the bulb socket and a wire is loose. To check both, Loosen the screw knob on the underside of microscope and open the panel to expose the bulb. Use a small screwdriver to loosen the screws holding (the two screws closest to the bulb) the prongs of the halogen bulb. Note that the prongs of the bulb are held in place by small brass plates which shift slightly when the screws are loosened. Remove the old bulb. Important: Do not touch the new halogen bulb with bare hands. Wear gloves or hold the bulb using tissue or lens paper. Body oils may damage the halogen bulb. Insert prongs of replacement bulb into top of socket (above the brass plate) and tighten screws slightly. (The brass plates will move up to hold the prongs in place.) Close door and hand tighten the thumbscrew knob.
If this does not work, contact Premier for assistance: Premiere® Microscope Service, 7241 Gabe Court, Manassas, VA 20109 (703) 330-1413
12/19/2017 4:57:03 AM •
Science &...
•
929 views • 0 helpful votes
I have inherited a Nikon
I think the number you gave is the microscope serial number, to hope to get help you need to find the model number so people can help. At least post a picture. In general the microscope needs a light source to be bright enough to use. The transformer is meant to provide power to the light. If you use the microscope with a light shining through the object held by a glass slide then the light is below the stage which holds the object. Sometimes on simpler microscopes they have a mirror below the stage and you shine a bright light beam into the mirror and must adjust the angle to reflect the light through the slide. In more complex systems the light is built into the microscope. For opaque objects you must shine the light from above onto the object. If you can't find the official Nikon light source to connect to the transformer, you may be able to get non Nikon light sources. For my stereo microscope for example, I use a LED ring-light I bought on ebay for ~$25. This lights the objects from above and fits around the microscope tube just above the stage.
12/18/2017 6:54:03 PM •
Science &...
•
593 views • 0 helpful votes
Can I put a 40x microscope lens into an ultrasonic
Soak in a product like lime away first. Glass lenses cant warp without heat. Plastic even crystal type can absorb minerals. Ultrasonic can help clean all of them. The lime away will remove almost all trace minerals, lye or powdered drain cleaner will remove organics. Gool luck let me know how these ideas woek for you.
11/29/2017 7:06:03 AM •
Science &...
•
541 views • 0 helpful votes
Heraeus pico biofuge
Are you sure that the lid safety interlock switch isn't damaged/dirty? If the centrifuge can't detect that the lid is closed it will never start. Sometime it just needs an extra push down on the lid.
9/10/2017 4:03:03 PM •
Science &...
•
1,734 views • 0 helpful votes
Not finding what you are looking for?