Saws - Page 7 - Answered Questions & Fixed Issues
Husqvarna K970 power cutter saw gas powered engine.
FIRST TIME EVER USED IT ? 6.5h ENGINE HERE.got spark, THIS IS FIRST, using fresh plug to test.got fuel? or is it super old fuel.canT burn gas , lacking spark , the engine may have compression release just like huge single cylinder motor cycles have, and can fail. but just harder to start failed.ASK MAKER FOR HELPTOP CAUSES (BY ACTUAL USAGE FAILURES)SO THIS TOOL SITS LONG TIME UNUSED? NOT TOLDBAD OLD FUEL AND FILTERS AND CARB. DIRTY.ENGINE IS 2CYCLE , GAS AND 40:1 OIL MIX OR PER MANUAL.FUEL FILTER PACKED, AIR FILTER PACKEDspark plug fouled, put in new. and gap it.and this.EASYSTART SYSTEM.The engine and starter are designed to ensure quick andeasy starting of the machine. Reduces the pull resistancein the starter cord by up to 40%. (Reduces thecompression during startingSEE PAGE 6https://www.lsengineers.co.uk/media/advice_centre/Husqvarna/Power-Cutters/operators-manual-k970.pdfSEE PARTS.
https://www.husqvarnaconstruction.com/us/power-cutters/k970/?article=967348001
12/28/2022 1:09:49 PM •
Husqvarna Saws
•
Answered
on Dec 28, 2022
•
103 views
Kobalt 24v brushless reciprocating saw seizes when you pull trigger. It clicks (light comes on) but blade won't move
It sounds like you are experiencing an issue with your Kobalt 24v brushless reciprocating saw. There could be a few potential causes for the saw to seize when the trigger is pulled and the blade won't move. Here are a few things you can try:
- Check the battery: Make sure that the battery is fully charged and properly installed in the saw. If the battery is low or not seated correctly, the saw may not have enough power to operate.
- Check the blade: Make sure that the blade is properly installed and tightened. If the blade is not properly installed or tightened, it may cause the saw to seize.
- Check the motor: If the motor is not functioning properly, it could cause the saw to seize. You may need to have the motor checked by a professional if this is the case.
- Check for debris: If there is debris stuck in the blade or in the saw, it could cause the saw to seize. Carefully remove any debris that you find.
If these troubleshooting steps do not resolve the issue, it may be necessary to take the saw to a repair shop or contact the manufacturer for further assistance.
12/27/2022 4:13:28 PM •
Blade Saws
•
Answered
on Dec 27, 2022
•
95 views
Lower blade guard alternatives?
Hi,
It sounds like you've called all 3rd party locations. Please call Bosch directly and request the part. And if they don't have it in the U.S. then you can request the phone number for their international locations. The U.S. phone number is 1-800-944-2904. Otherwise, I would search on ebay and alibaba to find the part that you've mentioned.
Thank you.
12/27/2022 1:22:53 AM •
Bosch Saws
•
Answered
on Dec 27, 2022
•
48 views
Changing my blades on a DeWalt 735.
The cutterhead is now exposed. If the eight screws in
the cutterhead clamp are not visible, use a piece of
scrap wood to carefully rotate the cutterhead (Fig. S)
until the screws are accessible and the cutterhead lock
lever18engages. This will prevent further rotation of
the cutterhead as you change the knives
12/8/2022 8:54:53 PM •
Dewalt Saws
•
Answered
on Dec 08, 2022
•
60 views
Not finding what you are looking for?