Saws - Page 6 - Answered Questions & Fixed Issues

https://www.repairtoolparts.com/black-decker-parts/black-decker-7301-type-2-parts-list

Question edited for clarity. Question moved from Cars and Trucks category. In the link https://www.google.com/search?q=hobart+5801+meat+saw+wiring+diagram Manual

MODEL 5801 MEAT SAW

https://www.alfaco.com > 2016/11 > 5801-Manual PDF SAVE THESE INSTRUCTIONS. GENERAL. The 5801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant. 12 pages ..

you need Blade Locking Assembly Part Number: 1085049-10 look on line from lowes or copy and paste https://awsparts.com/108504910-blade-locking-assembly ..

It probably has a left hand thread. The rotation of the saw tightens tightens it. Look at the rotation of the blade and imagine the allen key in the hole, would it tighten the screw or loosen it when the blade turns. For a left hand thread you would turn clockwise to undo it.

The battery is likely to be fine, but what about the electric motor in the saw, in rice as well? The only thing that tends to get damaged is electronic board components. Rice only works well if it was warmed first, silica gel packs are better. A couple of days should be good, but my advice it open it up straight away and dry with a hairdryer or heat gun.

It is likely that the trigger switch on your saw is faulty and not allowing power to flow to the motor. You may need to have the switch repaired or replaced by a professional. In the meantime, you may not be able to use your saw until the issue is resolved.

I have a piece to my jigsaw and I don't know what it is and where it goes it just fell out have a picture

Removing bearing #30571 on a Craftsman Radial Arm saw model 113.29003 can be a bit challenging, but it can be done with the right tools and techniques. Here are the steps you can take to remove the bearing:

1. Unplug the saw from the power source.
2. Use a wrench or pliers to loosen and remove the bolt or nut that holds the bearing in place.
3. Carefully remove the bearing from the saw. If it is difficult to remove, you may need to use a bearing puller.
4. Clean the bearing and the area around it with a clean rag or brush.
5. Inspect the bearing for any damage or wear. If it is damaged or worn, it will need to be replaced.
6. Once the bearing is removed, cleaned, and inspected, install the new bearing if needed, and reattach the bolt or nut to hold it in place.
7. Before turning the saw back on, make sure to test the saw operation before using it.

It is important to mention that this is a general guide, the exact steps and tools may vary depending on the particular model, so you may want to consult your saw's manual or the manufacturer for more specific instructions. Also, be aware that working with any power tools can be dangerous, always use the appropriate safety gear and take caution.

Question edited. Question moved from Cars and Trucks to model category. Help in the link, including Makita spares. https://www.google.com/search?q=makita+2703+dust+collection+bags ..

we are fixya,call sears for info

possible open winding

There could be several potential causes for the issue you're describing with your brushless 18Vlt paddle switch grinder.

1. Overheating: If the grinder is running for an extended period of time, it can overheat and shut off as a safety measure. If this is the case, the grinder will need to cool down before it can be used again.
2. Battery Issue: The grinder may be shutting off because the battery is not providing enough power. This can be caused by a damaged or worn out battery, or by a problem with the battery's connection to the grinder. Make sure the battery is fully charged, check and clean terminals, test battery with other tools, if there is no improvement consider getting new battery
3. Power switch issue: The switch could have a problem and it's malfunctioning, preventing the grinder from operating properly. The switch may need to be replaced in order to fix the issue.
4. Motor issue: A problem with the brushless motor itself, could cause it to shut off under load or malfunction. The motor may need to be inspected and repaired or replaced.
5. Power supply: If the grinder is running off of AC power, rather than a battery, the power supply may be faulty or not providing enough power to the tool.

I suggest you to start with trying to identify the problem by eliminating each possibility one by one. If you are not comfortable troubleshooting and fixing the tool, it may be best to reach out to the manufacturer or take it to a professional repair shop.

I'm sorry, but I do not have access to the instruction manual for the Ryobi HBT250 Table Saw. However, I can provide you with some general guidance on how to reinstall the motor on your table saw. First, make sure you have all the necessary parts and hardware before you begin. Before installing the motor, check that the motor pulley is properly aligned with the arbor pulley, and that the belt is properly tensioned. Next, you will need to mount the motor to the table saw. To do this, you will need to align the motor mount holes with the holes on the saw's base. Once the holes are aligned, use the bolts and washers that were provided with your saw to secure the motor to the base. Once the motor is mounted, you will need to connect the electrical wires to the switch and power source. The wires are usually color coded, with one wire being black or white (neutral), and the other wire being a different color (hot). The neutral wire should be connected to the white terminal on the switch, and the hot wire should be connected to the black terminal. After the motor is mounted and the wiring is connected, you will need to test the saw to make sure it is running properly. Turn on the saw and let it run for a few minutes to ensure that the motor is running smoothly and that the belt is properly tensioned. If the saw is running properly, you should be all set. However, if you are still having trouble, it may be helpful to consult the instruction manual for your specific model of saw, or reach out to a professional for assistance. Keep in mind safety instructions when working on the saw. If you don't feel comfortable with the task reach out to professional or consult the manual.

It sounds like you are having difficulty tightening the blade on your Bosch 1587vs jigsaw. To resolve this issue, first unplug the tool and lift up on the knob and loosen the spindle lock. Then insert the blade and push up slightly while doing so and twist to align the blade with the roller. Make sure to turn past resistance until it clicks. If the issue persists, you may need to replace the "clic" assembly, part #2-602-025-901.

Many parts are discontinued but this vendor has a good selection. https://www.mikestools.com/Delta-Replacement-Parts-Numbers-Starting-With-1_2297a.aspx https://www.google.com/search?q=Delta+saw+parts+1340243+or+1341608 ..

That is commonly called a throat plate and we need to know what the make and model of the saw is.

To replace the quick release blade holder on a Ryobi jigsaw, you will need to follow these steps:

1. Unplug the jigsaw and remove the blade.
2. Turn the jigsaw over and locate the blade holder.
3. Use a Phillips head screwdriver to loosen the screws that hold the blade holder in place.
4. Once the screws are removed, you should be able to lift the blade holder out of the jigsaw.
5. Insert the new blade holder into the jigsaw, making sure that it is properly aligned with the blade clamp.
6. Secure the blade holder in place using the screws that you removed earlier.
7. Reinsert the blade into the blade holder and make sure that it is properly secured.
8. Test the jigsaw to make sure that the blade holder is properly installed and functioning as intended.

It's important to be careful when replacing the blade holder on a jigsaw, as the blade is sharp and can cause injuries if handled improperly. Make sure to use caution and follow the steps carefully to avoid accidents.