Pool & Spa - Page 9 - Answered Questions & Fixed Issues

For a test only, remove filters and see if you feel anything against the fitting? If nothing either 'Air Lock', keeping it from priming the pump. Or, bad pump! Secondly, are you still dealing with a problem? Use the comment link on this thread, and let the forum know if you are, if repaired, what did you do? Intex link... Support Intex

You go down to reception and ask those facilities to add them to the room card. When they add them to the card, it alerts the reception manager that you have entered the pool area and someone will watch you on the CCTV for safety. In the business centre they are concerned with theft.

have you checked heater? If you do not have the tools or skill, you may better served having it checked.

With these automatic pool cleaners, if they are not staying firmly on the bottom of the pool, it is most likely that there is air in the appliance casing.Try submerging your cleaner. Keep the cleaner vertical while you are putting it in slowly to let the air out. Ensure the unit sinks to the bottom of the pool.

1. Check the wheel RPM. If not in the 30-36 RPM range, refer to the manual for adjusting the wheel RPM. 2. Adjust the thrust jet downward. 3. Verify the backup valve is cycling. Lift the valve out of the water and watch the jet. It should come on and go off. 4. Check for water inside the head float. 5. Empty the filter bag. You can download the 3900 Manual from the Polaris site http://www.polarispool.com/Pressure/Polaris-3900.aspx It will show you how to check the wheel rpm and how to adjust the thrust jet and check and adjust the float.

Check out the video and articles. Or email or phone the maker on Page 12 of the manual. It should really be installed by an electrician and must have a GFCI. https://images.homedepot-static.com/catalog/pdfimages/c0/c0a775b7-e7e4-46eb-96a4-77a6eacca9d4.pdf https://www.google.com/search?q=Xtreme+Power+75039+wiring+to+timer ..

If you have any clamp on amperage meters, you need to see what the amperage draw on the circuit is when it is running. This will tell you if something is wrong with the pump circuit. It could be anything from a bad capacitor to an impeller obstruction.

ask maker first?

Question edited for clarity, full 'make model (what it is)'. Pour hot water onto it to soften the end of the hose. Wear rubber dishwashing gloves to improve grip.

yes, the instructions do not specifies.

Usually resetting the 'Service' breaker on the main control box resolves this. If not, even though your remote receives data, you may still want to replace batteries in the remote. Next would be a faulty remote transceiver board ( cheaper to replace than the next item), in the unit with the antenna, or the mother board (the more expensive item).

test for circuit or motor failure

Question edited for full 'make model (what it is)'. Almost certainly yes. https://www.google.com/search?q=pdaps4+pool+temperature+sensor ..

possible ignitor bad

if screw holds impeller on it has a backwards thread remove then hold back of motor and turn off impeller regular threads

water getting into control panel is sorry a common failure on these , ruins electronics inside

Ideas and videos in the link. https://www.google.com/search?q=saluspa+inflatable+hot+tub+when+i+plug+it+i+it+lights+up+for+a+few+seconds+then+goes+off ..

Remeasure the pool cleaners hose to verify that it is adjusted to the proper length for the pool shape. With the Polaris operating, check that the swivels in the hose and the hose connections turn freely. Make sure feed hose is floating.With the Polaris turned off, spin each of the wheels. All wheels should turn together.

Cleaned pilot light area with an air compressor. Problem solved!

Question edited for clarity. Question moved to correct category. There is a video in the link that promises the codes, but it might be clickbait and an empty promise. https://www.google.com/search?q=Sta-Rite+400+code+337 ..