Garden - Page 8 - Popular Questions, Answers, Tips & Manuals
Living Accents Assembly guide for 8048106 pergola
1. Place the Pergola structure onto a flat surface in an area with adequate space for assembly and use.
2. Unwrap the hardware bag (included with the pergola) and place the contents on the flat surface near the structure.
3. Begin the assembly by attaching one of the long side rails to the top of the Pergola. Insert the rail into the slot at the top of the structure. Securing it with the provided hardware. Tighten the four screws using a drill to firmly secure the rail in place.
4. Next attach the second long side rail in the same fashion.
5. With both side rails firmly in place, attach the short side rails. Insert the rail into the slot at the top of the structure and then secure it with the provided hardware. Tighten the screws using a drill to firmly secure the rail in place.
6. Repeat this same process to attach the remaining short side rail.
7. Attach the four corner brackets using the provided lag bolts and washers. Some models may require different hardware for this step.
8. Secure the corner brackets with the provided bolts and washers.
9. Attach the remaining lag bolts into the holes in the top of the Pergola frame.
10. Tighten all the screws and bolts using a drill which will secure the frame in place.
11. Place the canopy (sold separately) on the top of the Pergola frame and secure it using the provided hardware and tools.
12. Once the canopy is secured in place.
10/31/2023 2:47:16 PM •
Garden
•
31 views • 0 helpful votes
Which wire needs to run to the battery to charge
Being unfamiliar with mowers, the battery seems accessible. So there is no need for having a socket or appoint other ways.
Trickle chargers have both cables, one with small clamps for the terminals and one permanent pigtail cable. The cable with plug that can be installed is always bolted onto the terminals.
Ground wires should be a distinct green/yellow color and the main negative is a thick one that just bolts onto engine or frame. A test will then find 12 Volt wires of those that are life when the engine is switched off. I don't have high hopes of those being many and charge is performed at maximum of 1/10 the battery Amp at most, usually it is much less like hundreds of Milliamp?re. Especially when a full charge is being reached. Also for metering the Voltage a battery installed cable is the right choice. It determines charge on tenth of a Volt. 12 Volt batteries are close to being depleted and 12,8 up to 13,2 Volt are full. Charging with the engine running would show 14,2 Volt on a motorcycle.
10/29/2023 1:11:14 AM •
John Deere...
•
32 views • 0 helpful votes
Ryobi bp42 backpack blower won't stay running and spit out gas
Common issues and possible solutions:
Fuel-Related Issues:
Check the Fuel Level: Ensure that the blower has enough fuel in the tank. If it's running low, refill it with fresh, properly mixed fuel as specified in the user manual. Remember to use the correct fuel-to-oil ratio to avoid engine damage.
Inspect Fuel Lines: Examine the fuel lines for any clogs, kinks, or leaks. Clean or replace them if necessary.
Clean the Carburetor: A dirty or clogged carburetor can cause starting and running problems. Remove the carburetor, clean it thoroughly, and check for any damaged components. Replace the diaphragm and gasket if needed.
Spark Plug Issues:
Check the Spark Plug: Inspect the spark plug for signs of wear, fouling, or damage. Ensure it's properly gapped and functioning. If needed, replace the spark plug
.
Air Filter and Intake System:
Clean the Air Filter: A clogged air filter can affect performance. Remove the air filter, clean it, and ensure proper airflow.
Inspect the Intake System: Make sure the intake manifold is secure and not loose. Tighten any screws or connections.
Heat Soak:
Sometimes, backpack blowers experience heat soak, where the engine becomes too hot to start. Allow the blower to cool down before attempting to restart it.
Compression and Ignition Coil:
Compression Test: Check the engine's compression using a compression tester. Low compression may indicate internal engine issues
.
Test the Ignition Coil: Ensure the ignition coil is functioning correctly. A faulty coil can lead to starting problems.
9/23/2023 10:05:01 PM •
Ryobi Garden
•
69 views • 0 helpful votes
Which wires to connect to a new solenoid on Dixon ztr 4516k?
The solenoid should have three posts. Two large contactor lugs and a smaller terminal for control (batt pos). The solenoid frame must be securely attached to the mower chassis as it is the control winding return path (batt neg).
The large gauge red wire from the positive battery post and 2 smaller red wires stack on to one contactor lug (post 1). The other large gauge red wire from the starter goes to the other contactor lug (post 2). The small yellow wire goes to the smaller solenoid control terminal (center post) and energizes the relay with battery positive from the ignition switch S (start) terminal.
Refer to attachment, wiring diagram.
10/15/2023 11:02:44 PM •
Garden
•
41 views • 0 helpful votes
How do I tell what year model my Kabota RTV900 XT is?
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjF7pm4xpSCAxVEmIkEHaPbAvoQFnoECB0QAQ&url=https%3A%2F%2Fwww.orangetractortalks.com%2Fforums%2Fthreads%2Fcan-i-determine-what-model-year-from-serial-code.45724%2F&usg=AOvVaw320X8niJs2M0dRBU5lxjT6&opi=89978449
10/22/2023 5:13:23 PM •
Garden
•
32 views • 0 helpful votes
BR 600 blower fuel line pops off
Leave fuel cap off and filter submerged. Ether fish out the fuel return or at least position where it's visible. Then press the purge bulb several times. Fuel should spurt out the return. If no fuel from return line and air bubbles come from filter, lines are reversed somewhere.
11/1/2023 2:09:39 PM •
Garden
•
26 views • 0 helpful votes
The diagram of how to replace the throttle cable on a Stihl 55 weed eater
I'm sorry, but I can't provide a visual diagram as I can't display images or diagrams. However, I can give you a step-by-step guide on how to replace the throttle cable on a Stihl FS 55 weed eater.
Before you begin, make sure you have the necessary replacement parts and tools.
Materials and Tools:
- Replacement throttle cable
- Screwdriver
- Pliers
- Allen wrench
- Socket set
Procedure:
- Safety First:
- Ensure the weed eater is turned off, and the spark plug is disconnected to prevent accidental starts.
- Remove the Air Filter Cover:
- Locate the air filter cover on the weed eater's engine and remove it. Typically, this involves loosening screws or clips.
- Access the Throttle Cable:
- With the air filter cover removed, you should be able to see the carburetor and the throttle cable attached to it.
- Disconnect the Throttle Cable:
- Carefully disconnect the throttle cable from the carburetor. This might involve loosening a screw or bolt holding it in place. Note how it is routed and attached.
- Remove the Handle Housing:
- Locate the throttle trigger on the handle housing and remove it. This may involve unscrewing parts of the housing or loosening screws to access the cable.
- Replace the Throttle Cable:
- Feed the new throttle cable through the handle housing and reattach it to the throttle trigger. Make sure it's properly connected.
- Reconnect at the Carburetor:
- Reattach the other end of the throttle cable to the carburetor in the same manner it was originally connected.
- Adjust the Cable Tension:
- Adjust the cable tension to ensure it operates smoothly. There should be some slack when the trigger is released but no excessive play.
- Reassemble the Weed Eater:
- Reattach the air filter cover, making sure it's secure.
- Connect the Spark Plug:
- Reconnect the spark plug and ensure it's properly seated.
- Test the Throttle:
- With all the components reassembled, test the throttle to ensure it's working correctly.
- Start the Weed Eater:
- Reconnect the spark plug and start the weed eater. Verify that the throttle is responsive and functions as expected.
This is a general guideline for replacing the throttle cable on a Stihl FS 55 weed eater. Keep in mind that specific models may have variations in their design and components, so refer to the user manual or consult with a professional if you encounter any difficulties during the replacement process.
10/18/2023 3:39:51 AM •
Stihl Garden
•
31 views • 0 helpful votes
Not finding what you are looking for?
