Food Mixers - Page 4 - Answered Questions & Fixed Issues

The machine needs stripping down as something it likely worn. The gearbox is also packed with grease and may need re-packing. They do need periodic servicing. Does it make the same noise with the bowl removed? Sometimes the noise will be attachments hitting the bowl. There is an adjustment screw underneath to see clearance. https://www.google.com/search?q=SMEG+Stand+Mixer+makes+loud+clanging+noise ..

Your'e good to go...Tip...keep the meat in a freezer for 30 minutes before grinding it. Apply olive oil in the interior parts of the unit to reduce the friction.

It sounds like there may be a few potential issues that could be causing the resistance you are experiencing:

1. Incorrect installation of the slow speed gear or key - If the slow speed gear or key were installed incorrectly, this could cause increased resistance in certain gears. Double-check the installation of these components to ensure they are properly oriented and positioned.
2. Stuck gears - If the gears and key are stuck on the drive shaft, this could cause increased resistance. Try removing the gears and key again, and make sure they are clean and free of any debris before re-installing them.
3. Improper alignment of the gears - If the gears are not properly aligned, this could cause increased resistance. Check to make sure the gears are properly seated and aligned with each other.
4. Damage to the worm wheel - The freshly chewed up center of the worm wheel could be causing increased resistance. Consider replacing the worm wheel if it appears to be damaged.

Overall, it may be helpful to consult the Hobart service manual for your specific model to ensure all components are installed correctly and to troubleshoot any additional issues that may be causing the resistance.

Try here.... https://www.oldhobartmixerparts.com/hobart-d300-mixer-grease.html Best to you

Possibly one screw for up and one for down, working on a see-saw mechanism.

It is a mechanical gear driven speed controller, so the lever is not attached at the back. https://www.google.com/search?q=b20+mixer+speed+control ..

Restoration https://www.google.com/search?q=Restoring+Kenwood+major+a707b Parts Diagram https://www.google.com/search?q=kenwood+major+a707b+parts+diagram Great information in the last link. You have to scroll a long way down the target page that is referenced here. https://hyperentang.wordpress.com/page/2/

Parts Distributors ' KENWOOD USA

https://www.kenwood.com > usa > Support > Parts_Dist... Replacement parts manuals and certain accessories not available from our Store may be ordered through the KENWOOD Authorized Parts Distributors listed below ... Missing: a707b ‎' Must include: a707b

A700 - Kenwood Chef Restore

https://www.kenwoodchefrestore.co.uk > Kenwood Che... A700 - Chef. Made in England - Kenwood, Woking, Surrey. ... Parts are obsolete. A -300 watt motor with centrifugal ... Download Instruction Manual - Here. Missing: a707b ‎' Must include: a707b

Kenwood chef A701A schematics - iFixit

https://www.ifixit.com > Answers > View > Kenwood+c... Sep 20, 2014 - Where can I find the schematics for a Kenwood chef model A701A in order to restore this machine?. Mike Jordan. Answer this question I have this ... 4 answers · 6 votes: I have probed my A701A and looked at one of the relevant patents. My provis ..

Question edited for a lot more clarity. Time for a new one. Nearly all parts are obsolete. https://www.ebay.com/itm/266100009365?epid=66794889 Parts Suppliers. I checked 3 of them https://www.google.com/search?q=EHC650+parts ..

It's perfectly save to use a power converter from 220v to 110V. The 50Hz Frequenz will let the Motor spin 20% slower. So it'll last forever. I use a KSM90 from the US in Germany for more than 25 years. It runs great and the gears inside it look like new.

it is not car or truck moved to mixers

It have been answered here before https://www.fixya.com/support/t1895314-200_mixer_brush_carrier_orientation More here https://www.google.com/search?q=hobart+a200+replace+brushes ..

That is a $10k to $20k mixer, depending on where you buy it. I have used one of these. Unfortunately, grinding noises that result in the motor stopping can be fixed with a power disconnect. Grinding noises = dry bearings, to seized bearings, to shredded or stripped gears. You need a Hobart Service Tech. https://www.google.com/search?q=Hobart+Legacy+HL200 ..

I'd give them a call they would be the best to get a more detailed estamate from. https://www.hobartcorp.com/locations?s=342

It sounds like there might be a switch in the arm, but I don't see one. It appears to be an Australian model so results found in North America may be skewed.. https://www.ereplacementparts.com/breville-bem800xl-5quart-diecast-stand-mixer-parts-c-116052_116058_116074.html Phone Breville and ask. You are the only person to report this issue, and to me it sounds like normal operation as everything works with the arm down. https://www.google.com/search?q=breville+scraper+mixer+pro+bem800xl+display+cuts+ou According to this there have been modification to the mainboard and shows a 'safety switch'. https://www.manualslib.com/manual/1771651/Breville-Bem800-Series.html#manual ....

Question edited for clarity. Question moved from Cars and Trucks to model category. The OP, George supplies the answer. Update solved: problem was the tiny speed control sensor mounted above on the motor with three cables.

West Bend does not support parts for mixers.

pretty much anything can be repaired ---if diy take apart and diagnose problem and order replacement part--or send out to a repair shop in your area ust make sure repair doesnt exceed what mixer is worth

It sounds like there may be an issue with the motor in your Kenwood Chef Premier mixer. This could be caused by a variety of factors, such as a malfunctioning motor, a problem with the drive belt or gears, or an issue with the electrical components of the mixer. To troubleshoot the problem, you may want to try cleaning and lubricating the drive belt and gears, as well as checking the electrical connections and fuses.