Food Mixers - Page 4 - Popular Questions, Answers, Tips & Manuals

That is a $10k to $20k mixer, depending on where you buy it. I have used one of these. Unfortunately, grinding noises that result in the motor stopping can be fixed with a power disconnect. Grinding noises = dry bearings, to seized bearings, to shredded or stripped gears. You need a Hobart Service Tech. https://www.google.com/search?q=Hobart+Legacy+HL200 ..

I'd give them a call they would be the best to get a more detailed estamate from. https://www.hobartcorp.com/locations?s=342

Question edited for clarity. Question moved to category. The speed lever is electronic. Videos and the part in the link. https://www.google.com/search?q=Kitchenaid+Professional+6+mixer+speed+lever+stuck ..

It is a mechanical gear driven speed controller, so the lever is not attached at the back. https://www.google.com/search?q=b20+mixer+speed+control ..

Question edited for full 'make model (what it is)'. There must be a spring in the base that helps the top rise when you depress the button. You will need to remove the base. The manual doesn't mention anything and there is no Service Manual https://www.manualslib.com/manual/1021018/Hamilton-Beach-63390.html?page=5#manual Very limited help here apart from JustAnswer dot com https://www.google.com/search?q=hamilton+beach+model+63390+mixer+tilt+button+not+working ..

I do not think it matters the plastic disc may be to keep beater fro mixing bowel. i would try it and see what happens, you could switch holes after trying it.

Question edited for a lot more clarity. Time for a new one. Nearly all parts are obsolete. https://www.ebay.com/itm/266100009365?epid=66794889 Parts Suppliers. I checked 3 of them https://www.google.com/search?q=EHC650+parts ..

Watch the videos and see if you did it correctly. The oil seal is tight in its seat so it can't be off centre. The best thing for bedding seals is a hydraulic press and a large socket. https://www.google.com/search?q=installation+of+Hobart+A200+oil+seal ..

It have been answered here before https://www.fixya.com/support/t1895314-200_mixer_brush_carrier_orientation More here https://www.google.com/search?q=hobart+a200+replace+brushes ..

It sounds like there may be an issue with the motor in your Kenwood Chef Premier mixer. This could be caused by a variety of factors, such as a malfunctioning motor, a problem with the drive belt or gears, or an issue with the electrical components of the mixer. To troubleshoot the problem, you may want to try cleaning and lubricating the drive belt and gears, as well as checking the electrical connections and fuses.

Help in the link including from Kenwood themselves. It is likely to be the selector, the control board or the motor. Take it in for Dealer Service. https://www.google.com/search?q=Kenwood+kmix+doesn%27t+start ..

Tip it on its side and spray it with kitchen cleaner spray. Wait 5 minutes and try again. It is probably gummed up from a messy cake job. FULL 'make model (what it is)' in all questions please, first 3 words. ..

it is not car or truck moved to mixers

It sounds like there may be a few potential issues that could be causing the resistance you are experiencing:

1. Incorrect installation of the slow speed gear or key - If the slow speed gear or key were installed incorrectly, this could cause increased resistance in certain gears. Double-check the installation of these components to ensure they are properly oriented and positioned.
2. Stuck gears - If the gears and key are stuck on the drive shaft, this could cause increased resistance. Try removing the gears and key again, and make sure they are clean and free of any debris before re-installing them.
3. Improper alignment of the gears - If the gears are not properly aligned, this could cause increased resistance. Check to make sure the gears are properly seated and aligned with each other.
4. Damage to the worm wheel - The freshly chewed up center of the worm wheel could be causing increased resistance. Consider replacing the worm wheel if it appears to be damaged.

Overall, it may be helpful to consult the Hobart service manual for your specific model to ensure all components are installed correctly and to troubleshoot any additional issues that may be causing the resistance.

Hi, This sounds like it's a portion of the whole product. If you want that, you might need to arrange an order through nuwave or one of it's manufacturer partners that focuses on the plastic enclosure tha that you've mentioned. If that does not work, then you can reach out to a commercial kitchen product distributor to help with find the part. To find one, you can check on the back of your kitchen product boxes . They sometimes show a "distributed by" phrase in those areas. Thank you.

Unfortunately not available anywhere online. Check eBay once every couple of weeks. https://www.google.com/search?q=Cooks+sm248+manual ..

Reset Malfunction is 6 Blinks. https://www.google.com/search?q=Hobart+Grinder+Mixer+blink+6+times MANUAL

mg1532 mixer-grinder (208-240/60/3) technical manual

https://img.sigmaequipment.com > equipment-docs PDF The exclusive Hobart designed #46 Wedge cylinder grinding end speeds product from hopper to grinding end by pulling pieces of meat through the large upper. 50 pages

West Bend does not support parts for mixers.

Question moved from Cars and Trucks. Stand Mixers don't normally have belts and I don't believe this one does as I can't find spare belts. They are operated by nylon cogs that run in grease. The most likely reason is the she shear pin has sheared. This is a small pin like a nail that goes through a cog or shaft and shears if too much load is put on the mixer beater or dough hook. It often happens if you make bread and have the speed too high. https://www.google.com/search?q=change+the+belt+in+a+Bodum+electric+mixer ..