The gas shutoff solenoid on your John Deere LA 130 is typically located on the bottom of the carburetor bowl, and it should be screwed in to secure it in place. If you have been turning the solenoid for 20 minutes without it coming off, it's possible that it may be stuck or there could be another issue preventing it from loosening.
Here are a few things you can try:
1. Apply penetrating oil: Spray some penetrating oil (such as WD-40) around the base of the solenoid where it screws into the carburetor bowl. This can help loosen any debris or corrosion that may be causing it to stick.
2. Use a wrench or pliers: If the solenoid has a hexagonal base, you can try using an appropriately sized wrench to provide additional leverage for turning it. Alternatively, you can use pliers to grip the solenoid tightly and turn it counterclockwise.
3. Seek professional help: If the solenoid still doesn't come off after attempting the above steps, it might be best to consult a professional technician or take your mower to an authorized John Deere service center. They will have the necessary expertise and tools to diagnose and resolve the issue safely.
Remember to exercise caution while working on your mower's carburetor and ensure the engine is turned off and cool before attempting any repairs.
It could be 2 things.
Either a shear pin has sheared and the paddle is sticking at the same spot.
or
The is a nylon cog inside that has lost teeth and it sticks there.
The only way to diagnose is to take it apart. It is a very MESSY job full of grease and oil.
https://www.google.com/search?q=hobart+mixer+hl200+parts+manual
..
Question edited for typo.
Two person job. Spray the locking lugs with WD40. One person holds the machine and the other turns the bowl anticlockwise.
Full 'make model (what it is)' is useful in these questions.
..
In the drive train there are shear pins that are soft enough to shear if the gears are strained. It happens on bread dough if you run the machine too fast or put a piece of bone into a grinder attachment.
Or, sometimes a gear will move. if not correctly shimmed.
https://www.google.com/search?q=Haden+Mixer+parts+diagram
..
The machine needs stripping down as something it likely worn. The gearbox is also packed with grease and may need re-packing. They do need periodic servicing. Does it make the same noise with the bowl removed? Sometimes the noise will be attachments hitting the bowl. There is an adjustment screw underneath to see clearance.
https://www.google.com/search?q=SMEG+Stand+Mixer+makes+loud+clanging+noise
..
Question edited for clarity.
Question moved from Sunbeam Cars
There are no instructions on disassembly because it is so old. There will be screws underneath. Oil will be grease that is degrading.
https://www.google.com/search?q=sunbeam+oskar+4816-8+disassembly
..
From what I know about these and industrial Hobart mixers is that where drive gears are on a shaft they are held by a shear pin that goes right through the gear and the shaft. They are made to shear if the grinder or planetary head is strained. It shears the pin instead of damaging the motor or shredding gears. When they do shear, there is often enough friction to turn the attachment, but not enough force under load. I see two shear pins in this diagram 19/8 and part 14/8. The diagram also show the orientation of bevel gears.
https://www.google.com/search?q=olympus+s924+manual
A Moulinex Coffee Mill might be a better solution for grinding wheat.
..
Your'e good to go...Tip...keep the meat in a freezer for 30 minutes before grinding it. Apply olive oil in the interior parts of the unit to reduce the friction.
Don't forget if it is new it is under manufacturer warranty.
Make the beater isn't too low and fouling, because the bowl is set too high? Try to lock with no beater.
pretty much anything can be repaired ---if diy take apart and diagnose problem and order replacement part--or send out to a repair shop in your area ust make sure repair doesnt exceed what mixer is worth
Question edited for clarity.
Question moved from Cars and Trucks to model category.
The OP, George supplies the answer.
Update solved: problem was the tiny speed control sensor mounted above on the motor with three cables.
There are several potential reasons why your KitchenAid dough mixer might be shutting off. Here are a few possible causes:
Overheating: If the mixer has been running for an extended period of time, the motor may overheat and shut off as a safety precaution. In this case, you should allow the mixer to cool down for a while before using it again.
Faulty wiring: If the mixer is shutting off when you turn it on or when you change the speed, there may be a problem with the wiring. You should check the wiring to see if there are any frayed or damaged wires that could be causing the issue.
Clogged air vents: The mixer may shut off if the air vents are clogged, as this can cause the motor to overheat. You should check the air vents to make sure they are clean and unobstructed.
Failed motor: If none of the above issues are present, the problem could be with the motor itself. A failed motor can cause the mixer to shut off, and it may need to be replaced.
If you are not comfortable troubleshooting the mixer yourself, you should consider contacting KitchenAid customer service or a professional appliance repair service for assistance.
