Irons - Answered Questions & Fixed Issues


I imagine that it would be the water valve not closing, allowing water to continue to enter the steam chamber. I have no idea how to get into these to have a look.

Irons | Answered on Mar 22, 2019 | 15 views


First thing to try is descaling it. Most manuals are online, Google
make model manual

Cleaning a Laundry Iron
Get some CLR descaler and mix it to the directions. Turn the iron on and set it to steam. Turn the iron off and put the CLR into it. When it has cooled a little, sit it faceplate down in an oven proof dish. Leave it over night. The CLR will drip through and sit in the dish cleaning the inside, and the topside of the soleplate. The next day, fill with water and shake upside down to empty any remaining CLR and scale through the fill hole. Keep filling and shaking to empty until the water comes clean.

If you don't want to use CLR, you can use white vinegar undiluted.
Cleaning Laundry Iron

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&ei=UNuTXMuAOsagtQWGsKHgCw&q=rowenta+steam+force+manual

Irons | Answered on Mar 21, 2019 | 18 views


I'm having a similar problem. I've used mine quite often a few years ago and went to use it recently and now no steam. I've taken my fcl-ss167 apart and there is a water filter inside the base. The water filter may be too full of calcium carbonate to pass water. The water filter is removable but I have not yet found one to replace it.
Photo supplied.
3_18_2019_12_16_50_pm.jpg

Irons | Answered on Mar 18, 2019 | 50 views


I would go online to the manufacturer's web site for the information.

Irons | Answered on Mar 16, 2019 | 26 views


Not here! We are FIXYA dot com, we are not who you think we are :>)

find the email confirmation, look for a phone number or an email address.

Irons | Answered on Mar 14, 2019 | 23 views


SEEMS I HAVE SEEN DESCALING LIQUID BOTTLES FOR SALE IN MANY STORES . SOME PEOPLE ACTUALLY DO IT WITH VINEGAR ALSO

Morphy Richards... | Answered on Mar 06, 2019 | 28 views


To disassemble the Russell Hobbs 15081 steam glide iron, you have to remove the two hidden screws on the handle. To locate the first screw remove the two adjacent blue buttons which are each held in with two hidden clips front and rear, so lever out with small screwdriver or similar. The second hidden screw is under the pivots of the water inlet lid.(I broke one of the plastic pivots but no big deal). Then using a thin blade, separate the top half of the handle from the bottom half of the handle. A bit of force is needed as there are more plastic clips. I started from the rear.
Once the top half the handle is removed, other screws become visible, so teardown is not hard, just note which screws go where, as they are different lengths.
My problem was that some of the screws/bolts were so corroded I needed to drill them out. The thermostat was also corroded, which probably explained why the thermal fuse had blown. The element was fine.

Russell Hobbs... | Answered on Mar 04, 2019 | 370 views


To disassemble the Russell Hobbs 15081steam glide iron, you have to remove the two hidden screws on the handle. To locate the first screw remove the two adjacent blue buttons which are each held in with two hidden clips front and rear, so lever out with small screwdriver or similar. The second hidden screw is under the pivots of the water inlet lid.(I broke one of the plastic pivots but no big deal). Then using a thin blade, separate the top half of the handle from the bottom half of the handle. A bit of force is needed as there are more plastic clips. I started from the rear.
Once the top half the handle is removed, other screws become visible, so teardown is not hard, just note which screws go where, as they are different lengths.
My problem was that some of the screws/bolts were so corroded I needed to drill them out. The thermostat was also corroded, which probably explained why the thermal fuse had blown. The element was fine.

Russell Hobbs... | Answered on Mar 04, 2019 | 64 views


There are no user serviceable parts in this device. unplug it for 2 minutes- make sure the reservoir is filled with water, and the power is off- plug it in and turn thee power on- wait for the ready light to illuminate and try to use it.
good luck
https://www.6ya.com/mrmmike

Irons | Answered on Mar 02, 2019 | 26 views


USE BRAIN FIGURE WHAT TURNS IT ON .

Tefal Irons | Answered on Mar 02, 2019 | 23 views


For more info about Iron keeps blowing trip when turned on:


Dial 1 844 441 2440 for free Garmin map update technical support

Irons | Answered Yesterday | 219 views

Not finding what you are looking for?
Irons Logo

Ask a Question

Usually answered in minutes!

Top Irons Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Brad Brown

Level 3 Expert

18002 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

Are you an Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...