Heating & Cooling - Page 4 - Recent Questions, Troubleshooting & Support

16x25

KSM-IW30WAE-7J1M

in the manual it will show what the diagnosis code is for a F1. Clean and check the air filter

clean the flame sensor

check continuity on switch

If you are using propane make sure the unit is set up for propane. If you are using natural gas make sure the unit is set up for natural gas. Next blow out piolet assembly with compressed gas. call me with any questions 3153418739

computer board has failed.

It is not the fan motor. it is most likely the computer board. can you take a picture of the unit and send it to me? text it to 3153418739

To fix code E5 on a Bonaire evaporative cooler, which typically indicates a water management issue, try the following steps:

1. Check the water level in the unit to ensure it's sufficient.
2. Inspect the water inlet valve for blockages or malfunction and clean or replace as necessary.
3. Clean the filter and pump to ensure proper water flow.
4. Reset the unit by turning it off at the power source, waiting a minute, and turning it back on.

If the problem persists, consult the user manual or contact Bonaire customer support for further assistance.

Let's troubleshoot this problem:

1. Check Wiring Connections:
   • Ensure that all wires connecting the IDU and ODU are securely connected. Loose or disconnected wires can cause communication errors.
2. Inspect Terminals:
   • Examine the terminals for any signs of damage or corrosion. Clean them if necessary.
3. Verify Correct Wiring:
   • Confirm that the wiring is correctly installed according to the manufacturer's specifications. Incorrect wiring can lead to communication problems.
4. Fuse Check:
   • Check if any fuses related to the AC system have tripped or blown. Replace them if needed.
5. Power Status:
   • Make sure the power supply to the outdoor unit is ON. If it's OFF, the communication cannot occur.
   86 Hitachi Air Conditioner Error Codes + troubleshooting - Arlington Air Conditioning Services (arlingtonairconditioningheating.com)

Just went through this after replacing Carbon filters. There is a 250V 15A fuse on one of the circuit boards but, by far, the more likely problem is incorrect seating of the front cover after replacing the filters. On the lower right side of the front cover is a rod which must go into the hole and engages a pressure switch that will kill power if the front cover is removed. This can be checked just by looking into the right hand side with the front cover installed. Ten second fix.

Question edited for clarity. Bad luck, and the company will get some negative advertising by your question as this will end up indexed by Google. There are some vendors for spare parts. If it is just a multicore wire that was damaged, that is available by the foot. https://www.google.com/search?q=human+touch+ZERO+GRAVITY+G+2+remote+replacement ..

Greetings from Mississauga, Ontario! If it is construction Styrofoam it is a good insulator. Fill as best you can between the studwork and use spray foam to fill gaps. Then cover with drywall. Floor insulation and underfloor heating is a good way to keep the chill out. Frozen pipes and only caused by cold and draughts. Stay warm. ..

The only thing that would cause this is something in the circuit is pulling too much electricity through that transformer. So what is the transformer hooked to? Please post the make and model

I assume this is a typical heater, with an on/off thermostat rather than temperature-dependent flame size controller. Make sure the burner is clean and the flame holes are not clogged. Also make sure the heat exchanger is clean, not loaded with ash or dust. Verify that you have adequate air supply to the heater (if the flame gets much larger when you have doors open all the way to the outdoors, you definitely have a problem, including a safety issue) and that the exhaust stack is not blocked. I've seen issues caused by bird or wasp nests in the vent plumbing. Check inlet gas pressure, and verify that the heater main gas valve is functioning. (If you have recently added another gas appliance, the piping may not permit adequate gas flow when both are running.) If you have your gas piped in from a utility company, you may have to ask them to verify adequate flow and pressure at the meter. Check the inlet to the gas valve to make sure it is not clogged with sediment (requires shutting off gas and removing the inlet plumbing from the valve).

Take the fan power switch apart and clean the 2 point contacts. Also clean the 4 male studs that the wires plug into. That should solve the problem.

Question edited for clarity, full 'make model (what it is)'. It may not have one

• Dual Powered - Hardwired or Battery

Their own manual is terrible, but it is Section 7 here Replacing the Batteries 1. Open the thermostat cover and locate the battery compartment door. 2. Remove the two "AA" alkaline batteries located in the battery compartment. 3. Install two new "AA" alkaline batteries into battery compartment. Make sure to match the positive (+) ends of the batteries with the positive (+) terminals located in the battery compartment. 4. Close battery compartment and verify that the low battery indicator does not appear in the display https://api.ferguson.com/dar-step-service/Query?USE_TYPE=INSTALLATION&PRODUCT_ID=3984136 https://thermostat.guide/proselect/proselect-pstsl21p52-2h-1c-programmable-thermostat-product-specification-guide/ ..

Check the breaker. They have a 5 year warranty.

Warranty - Franke HT-400 Installation Manual [Page 12]

ManualsLib https://www.manualslib.com > ... > Installation manual use, for a period of ?ve (5) years from the date of purchase. This warranty will be honored provided the HT-400. Heating Tank has been installed and ...

the 58-7958-4 is a Jobmate air compressor with a 3-gallon tank and a 1/3 HP motor. It has a model number of QLG160905BJ-076 G19-1D I could not find the exact part number for the motor brushes, but you may be able to find it on the label of the old brushes or by contacting Jobmate Product Support. You can also try searching for compatible brushes by using the model number of the motor or the air compressor. How to Replace the Motor Brushes on an Air Compressor (youtube.com)

From the owner's manual:

• Open front thermostat door and open battery compartment door.
• Install two new "AA" alkaline batteries. Locate the positive (+) ends of the batteries and match them with the positive (+) terminals located in the battery compartment. Close battery compartment.

Going by the photo of the thermostat, it looks like there's a finger recess or latch on the right side of the thermostat that you pull on to swing the front open. If there is unexpected behavior from the thermostat after replacing the battery, see the reset procedure in the installation section of the manual. Link to manual: https://thermostat.guide/proselect/proselect-pstsl21p52-2h-1c-programmable-thermostat-installation-guide/#battery-replacement