Hardware & Accessories - Page 5 - Answered Questions & Fixed Issues

If the fan won't shut off after replacing the Intermatic E-1020, there may be a few potential causes to consider. Here are a few steps you can take to troubleshoot the issue: Check the wiring: Double-check that the wiring is correct and that all connections are secure. Make sure that the Intermatic E-1020 is wired into the circuit correctly and that the fan is wired into the Intermatic correctly. Refer to the wiring diagram in the installation instructions to ensure everything is in the right place. Verify the settings: The Intermatic E-1020 has multiple settings, including time settings and override settings. Make sure that the timer is set correctly and that any overrides are disabled. Check the manual for the specific settings and instructions on how to adjust them. Test the switch: Verify that the on/off switch for the fan is working properly. Turn off the power to the circuit and disconnect the switch. Test the switch with a multimeter to ensure that it is functioning correctly. Check the fan: Verify that the fan is working properly. It's possible that the fan itself is faulty and is causing the issue. Turn off the power to the circuit and remove the cover for the fan. Test the fan motor with a multimeter to ensure that it is functioning correctly. If none of these steps resolve the issue, it may be necessary to consult with an electrician or HVAC technician for further assistance.

Pull out the center dial. Or just remove trippers after pulling out center dial.That action will stop ticking sound but wire will be exposed, so cover with tape.http://waterheatertimer.org/Intermatic-timers-and-manuals.html#E1020Add a comment. If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

The first thing you should check is that the time and location settings on your ej500 are correct. If they are incorrect, the timer may be turning off at the wrong time. Here's how to check:

1. Press and hold the "clock" button on your ej500 timer for about 3 seconds until the display flashes.
2. Use the "+" and "-" buttons to set the current time, making sure to set the correct AM/PM designation.
3. Press the "clock" button again to confirm the time setting.
4. Press and hold the "mode" button until the display shows "LAT" for latitude and "LON" for longitude.
5. Use the "+" and "-" buttons to set your location's latitude and longitude. You can find this information by doing an internet search for your city's coordinates.
6. Press the "mode" button again to confirm the location setting.

Once you have confirmed that the time and location settings are correct, try resetting the timer to its default settings by pressing and holding the "reset" button on the side of the device for about 3 seconds until the display flashes. Then, reprogram the timer to turn on at sunset and off at sunrise. Here's how to do that:

1. Press the "prog" button on your ej500 timer.
2. Use the "+" and "-" buttons to set the "on" time to "sunset" and the "off" time to "sunrise."
3. Press the "prog" button again to confirm the programming.

If the timer still turns off at 11 pm instead of sunrise, it's possible that there is a malfunction with the device. In that case, you may need to contact the manufacturer for further assistance or consider purchasing a new timer.

If the light on your Intermatic EJ500 timer is not turning off completely, it could be due to a faulty relay switch or a loose connection. Here are a few troubleshooting steps you can try:

1. Reset the timer: Turn off the power to the timer, wait for a few minutes, and then turn it back on. This will reset the timer and may fix any issues that were causing the light to stay on.
2. Check the wiring: Make sure all the wiring connections are tight and secure. If any of the wires are loose, tighten them with a screwdriver.
3. Replace the relay switch: If the relay switch is faulty, it may need to be replaced. You can purchase a replacement switch and follow the manufacturer's instructions for installation.
4. Check the light bulb: Make sure the light bulb is the correct wattage and type for the timer. If the bulb is not compatible, it may cause the light to stay on even when the timer is turned off.

If these steps do not resolve the issue, it may be best to consult a professional electrician or contact Intermatic customer support for further assistance.

If your Tork timer is turning on at times when it's not supposed to, there may be a few potential causes. Here are some things to check:

1. Check the programming: Make sure the timer is programmed correctly and that you have set the correct on/off times.
2. Check for stray signals: If your Tork timer is receiving stray signals from other devices, this could cause it to turn on or off unexpectedly. Try moving the timer to a different location, away from other electronics.
3. Check the power source: Make sure the timer is receiving a steady power source. If the power is interrupted or fluctuates, it could cause the timer to malfunction.
4. Check for interference: Interference from other electronics, such as nearby radios or TVs, could be causing the timer to malfunction. Try moving the timer to a different location or turning off nearby electronics to see if this solves the problem.

If none of these solutions work, it's possible that there is a problem with the timer itself and it may need to be repaired or replaced.

Le Saucier is a kitchen appliance that is used to make fresh butter and other creamy sauces. Without knowing the specific model of Le Saucier you have, it is difficult for me to provide an instruction manual for the automatic dial. However, here are some general instructions on how to use the Le Saucier:

1. Assemble the Le Saucier according to the manufacturer's instructions. Typically, this involves attaching the paddle and placing the machine on a flat surface.
2. Pour the cream into the Le Saucier. The amount of cream needed will vary depending on the size of the machine and the recipe you are following.
3. Set the machine to the desired speed and let it run. The automatic dial may allow you to set a specific speed or program, depending on the model.
4. After a few minutes, the cream will thicken and eventually turn into butter. Once the butter has formed, stop the machine and drain off any excess liquid.
5. Use a butter churn or cheese cloth to remove any remaining liquid and shape the butter into a desired form.

If you are still having trouble with your Le Saucier or need a specific instruction manual, I recommend contacting the manufacturer or searching online for a downloadable manual.

I'm sorry, but as an AI language model, I don't have access to information on specific product manuals or instructions. However, I can provide you with some general troubleshooting steps for a timer that is not working properly.

1. Check the power source: Make sure the timer is properly plugged in or has a fresh battery if it's a battery-operated device.
2. Check the settings: Verify that you have correctly set the timer for the designated time and that it is in the correct mode of operation.
3. Reset the timer: If the timer is not working as intended, try resetting it to its default settings.
4. Clean the timer: Dust and debris can affect the timer's functioning, so make sure to clean it thoroughly.
5. Seek professional help: If none of the above steps work, it may be time to seek professional help or replace the timer.

If you are still having trouble finding a timer specifically for your Westpoint DQP 12 set 9011, I would recommend reaching out to the manufacturer or a professional technician for further assistance.

Question edited for a lot more clarity. Question moved from Office Equipment to Timers. This timer has a fixed setting for turning on lights or appliances. To set the time, turn the small dial marked '8765' (which represent the hour when the lights will turn ON, so that the time you wish them to come on is next to the current time. In other words, if the current time is 6:00pm, and you want to have the lights come on at 8:00pm, set the 8 on the small dial next to the 6:00pm on the timer body, and plug everything in. ..

Based on the symptoms you have described, it's possible that there may be an issue with the ballast or the lamp in your Sunquest Pro 24 tanning bed. Here are some steps you can take to troubleshoot the issue:

1. Check the power source: Ensure that the tanning bed is plugged into a working electrical outlet and that the outlet is supplying the correct voltage. You can use a voltage tester to check the voltage.
2. Check the ballast: The ballast is a device that regulates the electrical current to the lamp. If the ballast is faulty, it may prevent the lamp from lighting up. Check the ballast for any visible damage or loose connections. If you're comfortable with electronics, you can also use a multimeter to check the ballast's continuity.
3. Check the lamp: If the ballast is functioning correctly, the issue may be with the lamp. Check the lamp for any visible damage or dark spots. You can also use a continuity tester to check the lamp's continuity.
4. Check the timer: If the timer is not functioning correctly, it may prevent the tanning bed from turning on or lighting up. Check the timer for any damage or loose connections.

If you're unable to identify the issue, it's best to contact a qualified technician or the manufacturer's customer service for further assistance. Tanning beds use high-voltage electrical components that can be dangerous if mishandled, so it's important to take proper precautions and not attempt to repair the tanning bed yourself unless you're experienced with electronics.

If there was a brief power outage and your light timer is not working, there are a few steps you can take to troubleshoot the issue:

1. Check the timer settings: Make sure that the timer is set correctly and that the time and program settings are accurate. If the timer has lost power, it may have reset and will need to be reprogrammed.
2. Check the power source: Ensure that the timer is receiving power by checking the outlet or circuit breaker that it is plugged into. If the outlet or breaker has tripped, reset it and try again.
3. Check the timer battery: If your timer has a battery backup, check the battery to make sure it is still functional. If the battery has died, replace it with a new one.
4. Reset the timer: If none of the above steps have worked, try resetting the timer to its default settings. Refer to the user manual for instructions on how to reset the timer.

If the above steps do not resolve the issue, it's possible that the timer has been damaged due to the power outage. In this case, you may need to replace the timer or seek the assistance of an electrician to diagnose and repair the problem.

It is not recommended to bypass the timer on your Smeg A2-2 oven, as the timer is an important safety feature. However, if you still want to bypass the timer, here are the steps:

1. Turn off the power to the oven at the main breaker.
2. Locate the timer wires. In your case, there are 2 black pairs, 1 red pair, and a single white wire.
3. Determine which wires are connected to the timer. These wires will be labeled "timer" or "clock."
4. Cut the timer wires close to the timer unit.
5. Strip the ends of the wires back about 1/2 inch.
6. Twist together the wires that were previously connected to the timer.
7. Cover the twisted wires with a wire nut.
8. Wrap the wire nut and wires with electrical tape.
9. Turn the power back on and test the oven.

Again, it is not recommended to bypass the timer on your oven, as this can be dangerous and may void your warranty. It is recommended to consult a professional technician or the manufacturer before attempting any repairs or modifications to your oven.

The Hurcon VX salt chlorinator timer should allow you to set the timer beyond 19 hours (7pm). If you are unable to set the timer beyond this point, it may indicate a problem with the timer or the programming. Here are some troubleshooting steps you can try to resolve the issue:

1. Reset the timer: First, try resetting the timer by turning it off and unplugging it from the power source for a few minutes. Then, plug it back in and try to set the timer again.
2. Check the programming instructions: Make sure you are following the correct programming instructions for the Hurcon VX salt chlorinator. Consult the user manual or manufacturer's website for detailed programming instructions.
3. Check the timer mode: Check that the timer is set to the correct mode, such as 24-hour time mode or 12-hour time mode.
4. Check the wiring: Check the wiring connections to ensure they are properly connected and not loose or damaged.
5. Contact the manufacturer: If none of the above steps resolve the issue, contact the manufacturer or a qualified technician for further assistance. It is possible that there may be a problem with the timer itself that requires repair or replacement.

Sorry, I can't find a User Manual anywhere on the net. You'll have to get the maker's address off the unit and write the company for a Manual.

If you are asking about modern vehicles then it is an electronic timer using a rev count from the crank shaft.

To set your Garrison timer model 52-8817-6 to operate properly, you may need to adjust the time and the mode settings. Here are the steps you can follow:

1. First, set the correct time on the timer. To do this, locate the "TIME" button and hold it down until the hour digits start to flash. Use the "+" and "-" buttons to adjust the hour, then press the "TIME" button again to move to the minute digits. Repeat the same process to set the correct minutes.
2. Once you have set the correct time, you can then set the mode. To do this, locate the "MODE" button and press it until the desired mode is displayed. In your case, you will want to set the timer to the "PM" mode.
3. Finally, set the on and off times for your device. To do this, locate the "PROG" button and press it to enter programming mode. Use the "+" and "-" buttons to set the on and off times for each day of the week.

If you have followed these steps and your timer is still not operating properly, you may need to consult the user manual or contact the manufacturer for further assistance.

It is generally not recommended to reuse a critical fastener like the rear spinal nut on your 2000 Ford Focus. These nuts are designed to provide a precise amount of clamping force and ensure proper alignment of the rear suspension, so reusing them may compromise the safety and performance of your vehicle.

You either have the time of day set wrong, or the Timer On/Off time is set wrong. https://www.google.com/search?q=garrison+52-8817-6+manual ..

This usually means that the batteries need to be replaced. Make sure you check the type of batteries needed for your timer, and replace them according to the instructions. If the issue persists after replacing the batteries, you may need to contact the manufacturer or a qualified technician for further assistance

It sounds like the program settings may not be saved correctly. You may want to try resetting and reprogramming the device to see if that fixes the issue. If not, it is possible that there could be a problem with the circuit board or the unit may need to be serviced if the issue persists.

It is possible that the issue could be related to the timer, however it may also be worth trying to reset the unit to the factory settings. This could help to clear up any lingering issues with the unit's settings that may be preventing it from running properly. If the issue persists after resetting, then you may need to check the timer or contact a qualified technician for further assistance.