Hand Tools - Page 5 - Answered Questions & Fixed Issues
Nail Gun support
Yes, because there is less risk of splitting the wood grain when using a nail gun than when using a hammer, nail guns are especially useful in delicate projects such as the application of indoor trimming. A nail gun sets the nail in one motion, reducing the chance of slips and bumps that can ruin delicate woods. Most models also include a rubber safety nose to protect the wood from friction.
My bht150 bostitch is jammed
First slide off the rubber grip This will expose a pin that you will need to remove. Remove the two bolts on top of the hammer with a 10mm wrench. These bolts hold the striker plate guide. Place the hammer in a vice to lightly compress the hammer head. Remove the allen head bolt located on the end of the head. This bolt holds the striker slid that strikes the staple. Remove the pin that you see that was under the rubber grip. Just tap with a punch and then you should be able to remove it with a small set of pliers. Now slid the enter assembly back just enough so that the jammed striker slid will come in contact with the striker guide face. Turn the hammer over and strike the top of the hammer on a piece of wood. This should free the slide and jammed staple. The staple and slide will come out. Take a file and deburr the slid and add a dab of grease to it. To reassemble, Attach the slide guide first, but leave it loose. The rest is reverse order. Hope this helps.
7/20/2014 2:12:15 PM •
Stanley Tools...
•
Answered
on Jul 20, 2014
•
9,730 views
How do i connect CBL-0084 l Frontpanel ?
Normally you will find the answer in your motherboard manual. The plug that connected to the front panel is keyed so it can only go in one way. Please reallize this is only a guess, as I do not know anything about your machine.
6/16/2014 6:10:47 PM •
SuperMicro...
•
Answered
on Jun 16, 2014
•
266 views
What kind of cable to run for HD update?
I ran regular RG6 through my house and both DirecTV and Comcast work just fine. Longest run I have from source to box is about 50' if that factors into your planning.
5/23/2014 10:20:16 PM •
RCA 12' Quad...
•
Answered
on May 23, 2014
•
271 views
I purchase a Lufkin tape measure and now the tape
When you pull it out eightteen inches, does it feel like it's under tension like normal? Is it retracting like normal? If so pull it out hard, in a quick tug, you probably got something in it. It's just bound.
3/28/2014 11:35:18 PM •
Hand Tools
•
Answered
on Mar 28, 2014
•
319 views
Rok power drill
Flame no, sparks yes. If the sparks are that big it's time to replace the brushes in the motor. it's an easy job, a hardware store will have them. Like mcclendons or do it centers. big box stores probably not.
3/28/2014 11:29:55 PM •
Hand Tools
•
Answered
on Mar 28, 2014
•
240 views
How much do manhole covers weigh?
Manhole covers are usually made from cast iron and so they are pretty heavy. They can weigh anywhere from 85 to 300 pounds.
1/16/2014 8:51:15 AM •
Hand Tools
•
Answered
on Jan 16, 2014
•
270 views
Stanley 10-777 utility knife: I need to reinsert
I had the same trouble. The blade holder was out of the knife and would not go back in. I fixed it this way: open the screw knob all the way to the least tension. Slide the two parts open but not all the way- there is a tab on the blade holder that gets in the way if you try to drop it in at the fully open position. With the two halves SLIGHTLY open- slide the blade holder in making sure that the tab is seated in it's slot. Depress the thumb tab and bring it to the most forward position and the two halves should be able to be seated together again.
12/12/2013 4:56:57 PM •
Stanley Hand...
•
Answered
on Dec 12, 2013
•
1,098 views
Mastercraft mitre saw
with regards to the stanley power stapler gun............replace the micro switch
12/4/2013 8:57:06 AM •
Hand Tools
•
Answered
on Dec 04, 2013
•
420 views
Not finding what you are looking for?