Hand Tools - Page 3 - Answered Questions & Fixed Issues

I don't know if you have been having higher then normal humidity where you live but one thing I have done for years that is inexpensive and easy is to wipe down your tools and golf clubs when not in use then spray them with WD-40.On my tools that hang in my shop I just spray them and leave the spray on. The tools that go in my tool boxes I spray and wipe lightly then put them on paper towel liners in drawers.I have my shop in a very old building with no heat unless I'm in it and have my stove burning so my tools are subject to extreme weather conditions. I do the same thing with power tool except being careful not to get any on the motors. I spray the table,blades and fence and mitre guide on my table saw and table,supportpole,gears and spindle on drill press and leave it on. It collect a bit more dust but cleans up easy.
The main ingredient in WD-40 is fish oil so it works great at displacing water and preventing rust. Thank you.

Only if it is connected to a telephone line.

put the knife to the wire insulation at about a 60 degree angle, and strip it like you are manually sharpening a pencil. sometimes it is easier after you heat up the insulation. or go to the store and get wire strippers for about 5$

they do make swagginhg tools that are fixed onto the yoke of a flaring kit. to hand swag, you should use the block of the flaring kit to hold your tubing. if you are swagging half inch tubing, hold the tubing up the diameter of the tube plus one eighth of an inch. tighten down the nut opposite the tube first then the closest one. this will keep the tubing from slipping.
Then hit it squarely with a hammer and it will bottom out at the flaring block. I would ease up on that last stroke to keep from cracking the tubing

Sorry to say, but Harbor Freight's parts list has no internal parts listed. So to fix it yourself, you may be able to find the little tiny diodes that usually go bad. They don't even have a wiring diagram in the owners manual.

Click on the 'Literature' tab here: http://www.mackay.co.uk/draper-expert-magnum-1000-workbench-86265-mwb1000-machine-tools-accessories-power.html - both manual and parts list available

Maybe it hepls you. On this website (link below) you find Fuse box layout and description for Volkswagen Transporter T5 Volkswagen Transporter T5 ESSENTIALS from September 2009 fuse box diagram...

Probably between 3 to 5 hours.
Check battery regularly. It should be warm while charging. When it begins to get hot it is charged. If you charge the battery for longer, there is the increased danger of fire or leakage from the battery.
Note how long the battery has been charged for and during for future charges, reduce the charging time.
NiCad batteries should be run flat before being recharged rather than being topped up in order to get maximum life out of the batteries. This is less critical with NiMh batteries.

wait for everything to get cool,if you keep your shades pulled and use room darkening shades,you wouldve come home to a cool house

On the handle press the rubber bump and fully remove by the hard plastic top of the pin

The black rubber grip has two bumps near the back one is rubber one is hard plastic. Squeeze the stapler togather and press on the rubber circle to eject the pin then remove the pin by the hard plastic end while keeping the stapler squeezed

From Superior Tool Website, look up the tool, then click on "How to Use". Blade Replacement: 1. Remove large pivot bolt and nut 2. Slide blade down through handle 3. Remove one (1) end of coil spring 4. Remove "E" clip from 1/4" pivot pin, remove pin and blade 5. Install in reverse order 6. Torque nut until tool ratchets correctly

I have it in a Word document. If you give me your email I'll send it.

I'd be willing to bet the yellow wire is really white just discolored and if so the that would be N for neutral the white wire, blue has been for the fan light ( L ) on the ones I've done so that would leave the red and T.

Put a little gun oil on the staples the spring that helps feed them might be catching

take a small brush like one you would use to clean a gun. clean it well and use gun oil to lube it

go to you tube there is a video that will help

I believe this is not even remotely the right forum to be asking this.

Gerber 600 replacement parts can be found on amazon. here: Amazon com Gerber 600 parts. I hope this was helpful. cheers

Removing Pucks