Hand Tools - Page 3 - Recent Questions, Troubleshooting & Support

may get a break down from the manufacturer on line but from experience junk it and get a new one easier on the nerves and less frustration

Check the store where you purchased the screwdriver but you will find its cheaper to buy a new screwdriver with new batteries than to buy just the batteries.

Another identical wp should be able to read your disk.. Did you try to replace the drive with another? Check ebay for parts? eBayeBay

turn the gun upside down and there is a silver slide plate left that up and there will be the location to load the brads

Have had the same problem but now it

Contact Black& Decker or better yet, Google for what you want. You will need to know the voltage {which you know} and the current draw and the size of the plug in to plug into your tool. There are universal chargers that will fir most tools.

Should be one on the inside.

There are no repair parts available. Hate to tell you but is a dispoable sander.

Just replace the broken belt with an O Ring of comparable size, it works great and you can't tell the difference!

there is a slide switch on top

I don't know if you have been having higher then normal humidity where you live but one thing I have done for years that is inexpensive and easy is to wipe down your tools and golf clubs when not in use then spray them with WD-40.On my tools that hang in my shop I just spray them and leave the spray on. The tools that go in my tool boxes I spray and wipe lightly then put them on paper towel liners in drawers.I have my shop in a very old building with no heat unless I'm in it and have my stove burning so my tools are subject to extreme weather conditions. I do the same thing with power tool except being careful not to get any on the motors. I spray the table,blades and fence and mitre guide on my table saw and table,supportpole,gears and spindle on drill press and leave it on. It collect a bit more dust but cleans up easy.
The main ingredient in WD-40 is fish oil so it works great at displacing water and preventing rust. Thank you.

Only if it is connected to a telephone line.

put the knife to the wire insulation at about a 60 degree angle, and strip it like you are manually sharpening a pencil. sometimes it is easier after you heat up the insulation. or go to the store and get wire strippers for about 5$

they do make swagginhg tools that are fixed onto the yoke of a flaring kit. to hand swag, you should use the block of the flaring kit to hold your tubing. if you are swagging half inch tubing, hold the tubing up the diameter of the tube plus one eighth of an inch. tighten down the nut opposite the tube first then the closest one. this will keep the tubing from slipping.
Then hit it squarely with a hammer and it will bottom out at the flaring block. I would ease up on that last stroke to keep from cracking the tubing

Sorry to say, but Harbor Freight's parts list has no internal parts listed. So to fix it yourself, you may be able to find the little tiny diodes that usually go bad. They don't even have a wiring diagram in the owners manual.

Click on the 'Literature' tab here: http://www.mackay.co.uk/draper-expert-magnum-1000-workbench-86265-mwb1000-machine-tools-accessories-power.html - both manual and parts list available

Maybe it hepls you. On this website (link below) you find Fuse box layout and description for Volkswagen Transporter T5 Volkswagen Transporter T5 ESSENTIALS from September 2009 fuse box diagram...

Probably between 3 to 5 hours.
Check battery regularly. It should be warm while charging. When it begins to get hot it is charged. If you charge the battery for longer, there is the increased danger of fire or leakage from the battery.
Note how long the battery has been charged for and during for future charges, reduce the charging time.
NiCad batteries should be run flat before being recharged rather than being topped up in order to get maximum life out of the batteries. This is less critical with NiMh batteries.

wait for everything to get cool,if you keep your shades pulled and use room darkening shades,you wouldve come home to a cool house

On the handle press the rubber bump and fully remove by the hard plastic top of the pin