Hammering - Page 6 - Answered Questions & Fixed Issues
Aeg ph26 drill
Inside a mechanical problem by the switch or other problem of a broken piece ring in front of the locking sleeve where the impact bolt fits the chisel.
Milwaukee PH26 or AEg PHE26
6/29/2016 4:19:15 PM •
Hammering
•
Answered
on Jun 29, 2016
•
651 views
Where do I put the oil?
Most breaker hammers have no oil if they have no high speed.
But special grease with high thermal conductivity.
very important .
If there is loose grease buy a consumables kit only complete , only then it makes sense.
6/29/2016 3:57:27 PM •
Hammering
•
Answered
on Jun 29, 2016
•
904 views
My bosch 11316evs pause during hammering
COld be the powercable (think on the electric field by the sliding contacts) or a to short carbon brush or a broken ring on the impact bold in front inside , pauze can be mechanical or electric.
6/24/2016 5:22:42 PM •
Bosch Hammering
•
Answered
on Jun 24, 2016
•
1,025 views
Started smoking from trigger
Maybe there is a interference suppression capacitor for radio supression near the switch have to only remove it . i do it by the most Bosch powertools because it made more problems than the purpose for which they are.
The ultra short wave radio listeners are not much more today everywhere its DAB+ do not suffer
5/31/2016 3:40:22 AM •
Bosch Brute...
•
Answered
on May 31, 2016
•
607 views
My hitachi jackhammer runs slow and gets hot
The armature AND electric field must together replaced to get a safe working again, and the defect will not repeat if it be shure have its operating hours on it and give a full service.
5/31/2016 3:28:31 AM •
Bosch Brute...
•
Answered
on May 31, 2016
•
1,092 views
My kango 637 breaker runs but no power is getting to the chisel canyou help please
There are a couple of main things that could cause this. Unfortunately this is an obsolete machine and I doubt you will be able to find any spares for it. Probable causes are worn seals/in need of service. Worn armature pinion gear and/or crank pinion gear. Ideally you should replace both if either one is damaged, even if the other one looks ok. There are always other possibilities but they it would need stripping on the hammer mech to check all the piston/pins/anvils etc. This is a very old machine (I cut my teeth on these when i started in the trade 20yrs ago).
5/18/2016 5:05:32 PM •
Hammering
•
Answered
on May 18, 2016
•
1,879 views
Kango 900 hammer:\r\nDon't know how to greace the
Milwaukee K900K or the English Kango 900K Blue old or Red some younger handle it differs very much English Kango was using a thick brown grease in 2 chrome colored plastic bags . the Milwaukee K900K has a lubrication grease also not oil but be aware of the operating hours i f you have a K900K model from Brand Milwaukee tools replace also a service kit and the bearings on the armature is important also Its neccesary to protect you from damage
if you have a English Kango its hard and expensive to get a spare parts and most times the tools are worn in the front of the chisel stroke bolds do not get right close and the piston pins are worn it was a good tool about 20 years ago i have serviced much of them . but the first thing thats important that its air-tight in front of the chisel and everywhere thats having a mechanic/pneumatic duty
Milwaukee Services and fill k900k with (IMPORTANT) the right number
4/17/2016 1:03:24 PM •
Electric...
•
Answered
on Apr 17, 2016
•
2,013 views
Not finding what you are looking for?
