Hammering - Popular Questions, Answers, Tips & Manuals


You need to check armature gear it can be damaged. Connection rod can be broken or you just need new o-rings and grease

Hammering | 37 views | 0 helpful votes


Hello,

You can try to watch this video: https://youtu.be/udj28_tLJvU

Dont forget to lubricate o-rings when mounting parts in. For flat x rings you can hold then in hot water to make them softer and thrn put ring in a place

Makita Hm0810b... | 30 views | 1 helpful votes


kango 950 was the hammer drill version. Usually when they stopped hammering they were due for a rebuild. These units have a aluminum piston that rides in a steel tube striker. When the 2 rubber piston rings wear out you will get the described problem. The Kango's use a special tan grease so you cannot just yank it apart and replace the 2 rings with o-rings and grease. I had to rebuild 15 900 and 950's because the previous mechanic used the wrong grease. https://project21designs.com/kango-950-parts
The link sells grease & rings.

Hammering | 17 views | 0 helpful votes


The GREASE for this heavy jackhammer
Makita 181490-7 Grease (if there are short carbon brushes to find ) replace all orings gaskets (and looking for an maintenance kit for this machine) 188015-8 thats the better way to service.

Makita Hammering | 291 views | 0 helpful votes


Buy a new switch the old switch was modificated by an maintenance kit if you have an old blue or red real Kango from England. or black Atlas Copco .
But if you have the red Milwaukee Kango then there is only a new switch to replace.

Hammering | 288 views | 0 helpful votes


burning motor
take it in for a check or junk it

Makita Hammering | 549 views | 0 helpful votes


  1. The total condition of the seal anvil piston and striker are very important for the total condition of impact when spending a service kit (maintenance) when there is leakage at the front part everything will be hot inside and the rings will harden again quickly.


kango 900 950 round switch housing

Hammering | 560 views | 0 helpful votes


Contact Arksen directly with your request.

Hammering | 522 views | 0 helpful votes


Connecting rod
Part Number:
315419-3
or
Woodruff Key 4
Part Number: 254001-2
Makita HM1211B Parts List and Diagram eReplacementParts com
Or broken spindle/ worn bearing(s)

Makita Hammering | 606 views | 0 helpful votes


BLACK+DECKER drill quickly replaced my cordless drill for all of the heavy duty tasks, and it continues to be a great "work horse". More details about the drill Best Hammer Drill

black-decker-dr670-hammer-drill-vqugf4lgsewrsyjnp2d3onew-4-0.jpg

Hammering | 552 views | 0 helpful votes


The efficient design of Ingersoll Rand 114GQC Air Hammer allows the users to quickly change the spindles on the drill. It is able to deliver 2-5/8 inches of strokes with a BPM speed of 3500 so it ensures total efficiency.

Bosch Hammering | 691 views | 0 helpful votes


Beware for all not all parts are more available, there is no oil used only Grease
Service Pack 1617000036 for Bosch Power Tool eReplacement Parts

Bosch Hammering | 977 views | 0 helpful votes


they usually heat shrunk on, to remove it you will probbley damage it.

Hitachi H45MR... | 626 views | 0 helpful votes


If selled some capacitor or new ignition parts order it always with statement of the serial motornumber and the year of build , because of modifications on marketing technical dicisions can be made for your engine, that can prevent a next disappointment. may be for the problem a new sparkplug the supression capacitor can also be bad a bad sparkplug connection cable .are some small sugestions.

Briggs &... | 705 views | 0 helpful votes


This is a possible problem. Check and see if the compressor has a fuse in it. If you have the manual it will tell you if it has a reset fuse if not check and see if the outlet there’s a fuse. I’ve had the same problem with the one I have. Hopefully it works if it doesn’t I’m sorry

Black & Decker... | 616 views | 0 helpful votes


contact the manufacturer thru their website .
or Google it replacement bits

Dewalt D25900k... | 541 views | 0 helpful votes




193243-2 revision maintenance service kit With all necessary rings and fat , beware before ordering an service kit take the time to remove all parts of the spindle ringing on the hammer tube spindle for cracks the chisel sds impact bold striker must be even air-tight on the chisel impact bold not leaking grease out of it , if its leaking the air flow will burn the o-rings in a very early time because of the building heat made by the leaking airflow . and loose of lubrication. fat grease .

Makita HM1100C... | 747 views | 0 helpful votes

Not finding what you are looking for?
Hammering Logo

1,767 questions posted

Ask a Question

Usually answered in minutes!

Top Hammering Experts

John Trevino

Level 3 Expert

1407 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2004 Answers

Are you a Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...