Grilling - Page 3 - Recent Questions, Troubleshooting & Support

First, remove the grill grates, then the flame tamers to access the burners. As you face the grill, carefully lift up the end of the burner farthest from you (It may or may not have a cotter pin holding it in. If it does, remove the cotter pin with a pair of needle nose pliers). As you lift it up, it should pull away from the burner orifice (inside the control panel). And that's all there is to it.To reinstall the burner, do everything in reverse. But, there is no need to replace the cotter pin. It was there for shipping purposes.

Hope this helped you. Please let me know. Happy Grilling!!

Question moved from Cars and Trucks category. You have a closed circuit switch somewhere. If depends on if you turn on the gas and in doing so it clicks and ignites, or whether you turn on the gas and and press a button where the battery is? The battery ones are simple and just have a spring that keeps the battery and the contact apart. Make sure it is in the right way around. For the type with microswitches, you would have to test each one with a multimeter.

If your Vermont Castings remote is burning through batteries quickly, there could be several reasons for this issue:

1. Weak signal: If the remote is having trouble connecting to the receiver, it may require more power to send the signal. This can drain the batteries quickly. Try moving closer to the receiver or replacing the receiver's batteries.
2. Short circuit: A short circuit in the remote can cause it to draw too much power and drain the batteries quickly. Check the remote for any signs of damage or wear and tear, and try replacing it if necessary.
3. Battery type: Make sure you are using the correct type of battery for your remote. Using the wrong type of battery can cause it to drain quickly.
4. Remote programming: If the remote is not properly programmed or is programmed for a different device, it may require more power to send signals. Check the remote's manual for instructions on how to properly program it for your device.

If none of these solutions work, it may be best to contact Vermont Castings customer support for further assistance or consider replacing the remote.

I can provide you with some general instructions on how to wire a 4 burner stove. First, ensure that the stove is disconnected from any power source. Identify the four burners and their respective control knobs. Each burner should have a set of wires connected to it. Remove the control panel cover by unscrewing any screws or bolts that hold it in place. Identify the wiring connections for each burner. The wiring should be color-coded, with one wire usually being black and the other white or red. Disconnect the old wiring connections by unscrewing any screws that hold them in place. Be sure to keep track of which wires go where. Connect the new wiring to the burner by attaching the black wire to the burner's terminal labeled "L1" and the white or red wire to the burner's terminal labeled "L2." Repeat steps 5 and 6 for each burner. Replace the control panel cover and secure it with any screws or bolts. Reconnect the stove to the power source and test each burner to ensure that it is working properly. It's important to note that these are general instructions, and the specific wiring diagram for your GE 4 burner stove may vary depending on the model and year. If you're unsure about the wiring or feel uncomfortable working with electricity, it's always best to consult a professional electrician or appliance repair technician.

Try contacting these folks..... https://www.partmaster.co.uk/help.pl Best to you

Ck here,,, https://www.youtube.com/watch?v=aD5BmaYTan0 May not be on the front but under it in the cabinet.

Honesty=Trust=Respect= Love and happy marriage.
But to answer your ? honestly I would have to say depending on if your talking about at what age you get married or age difference between to people. I assume your talking about age differences and I would have to say not really because if two people are in Love differences in age means nothing.

Here is your user and installation manual. Doesn't say much though. Usually panels can be removed. https://www.cookerspareparts.com/content/uploads/ApplianceModel/d561bfa7-204d-4d7c-84e7-5a1b27db89c5.pdf ..

Yes you can as long as your home uses LPG. You can not use 2 regulators. If your outside line is after your home regulator you need to eliminate the regulator on your grill. LPG products operate on 11" of water column, that's about 1/2" PSI.
Thanks for using Fixya
Jerry

Il n'est pas conseill? de contourner le d?tecteur de propane sur un moteur 91 Rockwood. Ce d?tecteur est install? pour d?tecter les fuites de gaz et assurer la s?curit?. Le contournement de cet appareil peut entra?ner une fuite de gaz dangereuse et pr?senter des risques pour les personnes et les biens. Il est pr?f?rable de faire diagnostiquer le syst?me de propane et de corriger tout probl?me plut?t que de contourner le d?tecteur.

There are several ways to obtain the operator's manual for the Traeger BBQ Model 155.02. Here are a few options:

1. Check the Traeger website: Traeger Grills often provides operator's manuals for its products on their website. You can go to the Traeger website and search for the model number of your grill (155.02) to find the corresponding manual.
2. Contact Traeger customer service: If you are unable to find the manual on the website, you can contact Traeger customer service. They can provide you with a copy of the manual or direct you to where you can find it online.
3. Check the box or packaging: Sometimes, the manual may be included in the box or packaging of the grill. If you still have the box, check to see if the manual is included.
4. Search on the internet: You can also try searching for the manual on the internet. Many websites such as ManualsLib, ManualsOnline and Google books, offer a wide range of downloadable manuals for various products including grills.

Be sure to check that the manual you are downloading is for the correct model number (155.02) to ensure that you have the correct instructions for your grill.

There could be a few reasons why the grease is not flowing into the outside bucket on your Traeger smoker. Here are a few things to check:

1. Make sure the grease bucket is properly positioned and securely attached to the smoker. It should be placed directly underneath the grease drain hole.
2. Ensure that the grease bucket is not full or overflowing. If the bucket is full, the grease will not be able to flow into it and will instead build up inside the smoker.
3. Check that the grease drain hole on the smoker is not clogged. Grease and food particles can build up and block the hole, preventing the grease from flowing into the bucket. Clean the grease drain hole with a pipe cleaner or toothpick.
4. Check that the grease bucket is not too cold. If the grease bucket is too cold, the grease may solidify and block the drain hole. Keep the grease bucket in a warm place to help the grease flow more easily.
5. Check your owner manual, if there is any specific troubleshooting steps provided, that can be helpful to solve the issue.

If none of these solutions solve the problem, it's best to contact the manufacturer or a professional for further assistance.

Yes, it is possible to use a Traeger smoker to heat something without getting a smoke flavor. One way to do this would be to use the "smoke" setting on the smoker to burn off any residual oils or flavors from previous smoking sessions, and then turn the setting to "high" or "bake" to heat the food without smoke. Another option would be to wrap the food in foil before heating it in the smoker, which can help to prevent smoke from permeating the food. It's important to note that even if you don't use the smoke feature on the Traeger, there may be still some smoke flavor present in the food, as the wood pellets will produce some smoke when they're heated, so you may want to consider using an alternative heating source if you want to completely eliminate the smoke flavor.

Sure, I'd be happy to help. Can you provide more information about the specific model of the Comfort Aire air conditioner you have and what part of the installation process you are finding confusing? Additionally, do you have the installation manual? It may have helpful information and illustrations.

To remove the igniter module from a Swiss Grill 460, you will need to locate the module and then follow these steps:

1. Disconnect the power supply to the grill to ensure safety.
2. Locate the igniter module. It is typically located near the burners and may be secured with screws or clips.
3. If the igniter module is secured with screws, use a screwdriver to remove the screws and gently lift the module out.
4. If the igniter module is secured with clips, gently pry the clips away from the module with a flat tool such as a screwdriver or butter knife. Be careful not to damage the clips or the module.
5. Once the clips or screws have been removed, gently lift the igniter module out of the grill.

I hope this information helps! Let me know if you have any other questions.

Did he change the reg as well ??

Try the maker direct. It doesn't appear online. https://www.google.com/search?q=ducane+2002shne+installation+manual ..

Sounds like the flame failure valve probe is not staying hot .Short or blocked flame that heats the valve or valve is on the way out

In the grilling category, so this is a BBQ Grill? Yellow flame is too much oxygen and not enough gas. It is normally cause by spider nests or other debris in the venturi tube where the gas and air mix. One is blocked completely. You can buy tubular brushes for this job. 'make model (what it is)' as the first three words in all questions please.

Send an email message to this address, [email protected], and I will send you a PDF copy of the manual. No SPAM or scam email messages please, I am simply trying to help this person out.