Drills - Page 5 - Answered Questions & Fixed Issues
Black and Decker 18 V 18 V battery charger light stays on red doesn't Flash just stays red and the battery doesn't charge Why is that and how can I Fix it
There could be several reasons why the Black and Decker 18V battery charger's light stays red and the battery doesn't charge. Some possible causes include:
- The battery is not properly seated in the charger. Make sure the battery is securely inserted into the charger's battery compartment.
- The battery is damaged and cannot be charged. Try using a different battery to see if it charges properly.
- The charger is not functioning properly. Try using a different charger to see if it charges the battery.
- The outlet or power source you are using is not providing enough power. Try plugging the charger into a different outlet or using a power strip with surge protection.
- The charger's fuse is blown or the charging contacts are corroded or dirty. Clean the contacts and check for a blown fuse.
If none of these solutions work, it may be best to contact Black and Decker's customer service for further assistance or to get a replacement.
1/17/2023 4:55:27 AM •
Decker Drills
•
Answered
on Jan 17, 2023
•
259 views
Drill master bad batteries or bad charger?
This could possibly be faulty batteries. Where are these batteries stored? If they are kept in a really cold place the batteries can 'cut out' and not charge until they have warmed up to room temperature. How old are these batterie and do they get used a lot? Batteries do get old and wear out. When both LED lights are on it is usually an issue with a shorted battery, (both lights on and NOT blinking), or a bad connection between the battery and the charger, (both lights on and blinking).
First unplug the charger and remove the battery. Take a close look at the connector pins on both to make sure there isn't dirt or something blocking the electrical contacts. Sometime the fix is that easy.
Next replace the charger. this is often your cheapest first step. That way you have a spare if the charger isn't the problem. If the new charger doesn't work it's the batteries that are faulty and they'll need replacing.
1/13/2023 7:31:48 AM •
Drills
•
Answered
on Jan 13, 2023
•
43 views
How do I take out the spindle on a 1675-1 Milwaukee hole hawk drill
To remove the spindle on a Milwaukee Hole Hawg 1675-1 drill, you will need to follow these steps:
- Disconnect the drill from the power source and remove the chuck key.
- Turn the drill over so that the chuck is facing upwards.
- Locate the spindle lock button on the side of the chuck.
- Press the spindle lock button and hold it down while rotating the chuck counterclockwise to loosen it.
- Once the chuck is loosened, you can remove it from the spindle by pulling it off.
- To remove the spindle from the drill, you will need to loosen and remove the retaining bolt that holds it in place. The retaining bolt is typically located on the bottom of the drill, near the front of the spindle.
- Once the retaining bolt is removed, you should be able to lift the spindle out of the drill.
It is important to follow these steps carefully to avoid damaging the spindle or the drill. If you are having difficulty removing the spindle, you may need to consult the owner's manual or a certified mechanic for assistance. They will have the necessary tools and expertise to help you remove the spindle safely.
What tension do i need on the belts of my ptbm500c3 pillar drill
In general, belt tension can be adjusted by turning the adjusting bolts located on the motor pulley or the driven pulley. These bolts can be tightened or loosened to increase or decrease the tension on the belts. It is important to set the belt tension to the correct specification to ensure proper performance and to prevent damage to the belts or other components.
Bosch GBH 2-18 RE doesn't go on
- Make sure the drill is properly plugged in and that the outlet is functioning.
- Check the power cord for any visible damage, such as frays or cuts, that may be preventing the drill from receiving power.
- Check the switch or trigger for any debris or foreign objects that may be preventing it from functioning properly.
- Check the battery for any visible damage or corrosion. If the battery is damaged or no longer holds a charge, it may need to be replaced.
1/3/2023 11:29:16 PM •
Bosch Drills
•
Answered
on Jan 03, 2023
•
52 views
My Metabo charger ICS 10 turns off when I put battery for charging?
Hi,
Please check that your battery is oriented properly and that it's not past it's expiration date (usually found written on the battery). Also, the temperature of the room where the charging takes place should be within the range advised by the manufacturer. If the location is too hot or cold, then charging might not take place.
If all of these things are taken care of, but the problem persists, then you can setup a repair/replacement with Metabo by calling them at (610) 436-5900.
Thank you.
12/28/2022 2:52:37 AM •
Drills
•
Answered
on Dec 28, 2022
•
437 views
My dc18ra makita battery charger flashes red and green lights no matter how many bateries i try
The pcb inside the battery has a microcontroller that monitor the
charges and charge cycle. When the cell falls below a certain voltage,
it will instruct the charger not to charge and will show with a
red-green flashing light. If the battery has been tried 3 times in
succession then the pcb will brick itself from the makita charger. So
first replace the bad cells. There are 2 solutions at this moment:
charge with a 3rd party lithium charger like the imax b6 or replace the
pcb with a working one. check out my blog on
http://mkbl1830.blogspot.com/
Not finding what you are looking for?