Cameras - Page 5 - Popular Questions, Answers, Tips & Manuals
My Eliminator Intelligent Battery Charger, now flashes 000 regardless of what battery I put it on. Can I reset it and get my charger working again?
you can try to reset your charger and get it working again:
Check the battery voltage: Use a voltmeter to check the voltage of your battery. If it's below 3 volts, it may be too low for the charger to detect. In this case, you may need to use a different charger or replace the battery.
Check the connections: Make sure that the battery terminals are clean and securely connected to the charger. Loose connections can cause voltage drops and prevent the charger from detecting the battery.
Check the fuse: If your charger has a fuse, check if it's blown. A blown fuse can prevent the charger from working properly.
Reset the charger: Unplug your charger from the power source and remove any connected batteries. Wait for 10 seconds and then plug it back in. This should reset your charger and clear any error codes.
If none of these steps work, you may need to contact customer support
10/28/2023 5:55:17 AM •
Next Cameras
•
54 views • 1 helpful votes
Error clock R49 error on Nikon D80
this error message is usually caused by a low battery. Here are some steps you can try to fix the issue:
Remove the battery from your camera.
Fully charge the battery using the Nikon D80 battery charger.
Remove the memory card and reset the camera by using the reset option in the menu or by pressing the reset switch on the camera's body, under the connector cover .
If the error persists, Nikon recommends waiting for one or two days before sending the camera in for inspection
10/28/2023 5:45:02 AM •
Nikon Cameras
•
53 views • 0 helpful votes
I got a Passonic Lumix DMC-TZ30 and it says "Mode dial is not in the proper position
Make sure the picture of the setting you are using on the turn dial is lined up with the beige pointer on the top of the camera. When you turn the dial, you can feel it lock into position. It could be that the dial hasn't quite clicked into the right position and just needs adjusting
https://www.avforums.com/threads/panasonic-tz3-mode-dial-is-not-in-the-proper-position-repaired.1419963/
10/23/2023 3:15:17 PM •
Lumix Cameras
•
47 views • 0 helpful votes
Moultrie Game Camera shows 'No Memory'.
The make dozens of models and no model stated.
This can happen for 3 reasons.
The memory card is too big and not recognized.
The memory card is not the right type.
The memory card wasn't formatted inside the camera.
Google 'make model manual' and check.
How can i get chain for Bauholtz pole saw 27564
Sadly we don't have this sort of information. Have you tried contacting Bauholtz directly? You could also ask at some power tool specialist repairers as they may be able to suggest other replacements. As to the cost of delivery, only the company you buy it from can tell you that!
10/9/2023 9:51:04 AM •
Cameras
•
32 views • 0 helpful votes
JVC GR-FXM40EK camera will no longer turn on.
Battery for cameras are normally made a specific shape or size so they only fit that camera and yours is just like that. The batteries to wear out and degrade so much that they came be fully charged (or never charge) and dissipate that power in 4 minutes from full to 'not enough power to operate'. The only difference with batteries is the number of Milli Amp Hour figure, the more mAh, the longer the camera works on a charge. The spec on yours is
GR-FXM40EK Camcorder Battery 6 volts 2100mAh
It was launched in 2003 and has probably been sitting in a cupboard for 10 years. The first thing to do it get a replacement battery and charge it up. In the leads that you got with it, there may be one to run it on mains power through an adapter. A battery is $10 a battery and charger is $33.
https://www.psaparts.co.uk/camcorder/jvc/gr-fxm40ek-battery-adapter-charger.html
https://www.google.com/search?q=JVC+GR-FXM40EK
..
9/26/2023 8:16:17 AM •
JVC Cameras
•
38 views • 0 helpful votes
My camera not detect the SD card memory
AI Answer Bot answer deleted. Its waffling answer misses the two most important facts.
First you don't supply the make and model of your camera, so I can't check your online manual, but the two reasons are.
1. The card has to be formatted within the camera. There is a setting 'format SD Card'. It has to be done within the camera as they all use a proprietary file storage system.
2. SD Cards are so cheap now, so you buy a quarter terabyte card (250 GB) to give you lots of storage, BUT that camera can only recognizes 8, 16, 32 GB as a MAXIMUM. This is why you need to mention the camera make and model so I can check.
My usual speech is "all questions need 'make model (what it is)' as first 3 words in every question :>D
..
9/1/2023 12:03:32 PM •
Cameras
•
62 views • 0 helpful votes
Not finding what you are looking for?