Dehumidifiers - Page 7 - Answered Questions & Fixed Issues

Here are all the spares, but no sensor. Contact the maker direct. https://www.meaco.com/collections/spares ..

You need a full strip down, clean and look for holes or failed sealant.

My unit runs for a half hour and then theme dreaded E9 comes up. Then the fan runs but no buzzing from the condenser. Sounds like everyone who buys this brand has this problem !! I will try the manic press and hold the start button and hope it works.

The full light normally comes on when the tank is full. Emptying the tank and re-installing the tank should allow the system to reset. However, if the tank isn't pushed in all the way... the full switch and indicator light will be fooled into reporting a full condition. My suggestion is, first pull out the tank, look at the float and the tank full switch. Become familiar with these two items and confident that 1) the float is not stuck in the up position; 2) the tank full switch that the float is supposed to actuate will toggle (press your finger against it and let it return.) After this exercise make sure the tank is seated all the way in place. If your issue is mechanical, its easier to fix than if it's electrical, and if it is electronic... (just pray that it isn't).

google it up

Thank you for your post, friend!

I see that your question is if the fan should shut off once it has reached the recommended setting. The fan will run even when the compressor cuts off so that air can pass over the sensor coils to check the humidity. This is a normal operation. I hope this is helpful. -Matt

maybe a clean the filter warning? find your instruction manual or download a new one from the mfg

Apparently NOWHERE! Contact DeLonghi direct https://www.delonghi.com/en-int/products/comfort/air-treatment/dehumidifiers This search query should have shown lots of places, Maker direct, Amazon, eBay and Appliance parts suppliers like Part Select dot com. It's very odd. https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00f9Jx3klLUl0dKNUo5ffEHVuQLMA%3A1612057058213&ei=4gkWYNW0DJWq1QGmg6TQAg&q=DeLonghi+DN+125+R+Dehumidifier+replacement+filter ..

the float is maybe stuck. find it and free it

Contact Air Force directly to request the manual.

There are a several things that can mimic a faulty humidity sensor.

1. The air intake filter is clogged and needs to be removed and cleaned.

2. The coiling coils need to be cleaned.

3. Ambient air temperature at floor level is between 40 - 60 degrees.
dehumidifiers do not work well between those temperatures
(Unless, you have a Low Temp Unit). This applies mainly to
where the air temperature at floor level is colder than at shoulder level
in basement applications. Raising the unit up off the floor,
onto a sturdy table, counter top, etc, that can handle the weight
of the unit, plus a full tank of water, will usually resolve this
problem.

If the above fails to help solve the problem, replacing the Humidity Sensor is certainly an option. But, before you jump into it, make sure you have an accurate wiring diagram, so you know which sensor is which. As the part does not come with installation instructions.

I hope this helps you and thanks for choosing FixYa.

Some dehumidifiers have provisions for connection of an ordinary garden hose to drain into a tub, a standpipe, or a sump pit.

how do i stop the alarm coming on after 30seconds ive cleaned the filter but light still comes on

Hi,
Here is a tip that I wrote about that problem...

http://www.fixya.com/support/r4662409-dehumidifier_running_but_no_water_in

heatman101

Return for replacement

Try contacting Whirlpool to request.

try where you got the unit

https://www.google.com/search?q=Amcor+D250+Dehumidifier+manual&rlz=1C1CHBF_enUS757US757&oq=Amcor+D250+Dehumidifier+manual&aqs=chrome..69i57j0i22i30i457.5311j0j4&sourceid=chrome&ie=UTF-8

Your dehumidifier could be low on refrigerant.

https://www.appliancefactoryparts.com/search/part/283125/116713/