Dehumidifiers - Answered Questions & Fixed Issues


It will help as long as you have enough airflow over the coil to prevent it from icing over. The longer the AC runs the more moisture it can remove. However, before you change the fan speed be sure Saturation is correct. As I hinted too low of a fan speed can also have repercussions. https://www.youtube.com/watch?v=VtYgi9wKTcQ

Dehumidifiers | Answered on Mar 13, 2019 | 20 views


There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few . reliable-store
let me know if u need help
thanks

Dehumidifiers | Answered on Mar 01, 2019 | 39 views


No there is no need. You are recirculating the air in the room and removing moisture from it into a tank in the machine.

Dehumidifiers | Answered on Feb 22, 2019 | 26 views


Google (simplicity)(380)(manual) without parens for instructions.

Dehumidifiers | Answered on Feb 20, 2019 | 30 views


return it to place purchased with out doing anything it has or had warranty if you only added water still

Dehumidifiers | Answered on Feb 20, 2019 | 28 views


I think what you're actually seeing is an AS error. It's looks like A5 on the LED screen.
AS error means their is a sensor failure. So, before calling Frigidaire Tech Service
(800-444-4944), turn the Master On/Off Switch to OFF. Unplug the unit for 12 - 15 minutes.
This should give the unit ample time to reset itself. Plug the unit back in and turn the Master ON/Off Switch to ON. Now, set your controls as you normally do. If the unit starts up and runs as it should, the problem for now is solved. If it keeps re-occurring, contact Frigidaire Tech Service.

Frigidaire... | Answered on Feb 11, 2019 | 1,720 views


Dehumidifiers seem to be prone to cabinet rattles because of vibration from the compressor.

Soleus... | Answered on Feb 06, 2019 | 28 views


Usually happens when the float valve is stuck in the down or up position try wiggling the handle to release or if the collection bucket is not sitting perfectly on the safety switch has to be down square I have the delonghi dem10 model always empty and unplug before checking

DeLonghi... | Answered on Jan 31, 2019 | 35 views


Dehumidifier typically use a float in the collection bucket to detect water level and automatically shut it off once it's full. Have you checked to see if the float is broken or missing? Also sometimes it can get stuck ir jammed up when inserting the bucket, make sure its in place and falling freely down into the bucket.

Dehumidifiers | Answered on Jan 30, 2019 | 42 views


POSSIBLY THE MFG'S WEBSITE

Dehumidifiers | Answered on Jan 26, 2019 | 46 views


the humidity sensor is usually in the front of the unit take the front housing off look for a small long sensor and clean it off it may just be contaminated with dirt so on.

Dehumidifiers | Answered on Jan 21, 2019 | 48 views


Not many people use dehumidifiers in the middle of the winter; Are you in a warm weather state? The dehumidifier should have a moisture percentage control. Simply dial it to the desired level. I would suggest setting it to 50% and checking your reservoir in a few hours for any water. Do you have a humidity gauge so that you can see what is the current room condition of humidity? I would be happy with 50%, but you may need something different. Good luck.

Dehumidifiers | Answered on Jan 14, 2019 | 69 views


I bought one of the FDL70S1 Frigidaire dehumidifiers today for my shop, and found that the $5 hose I bought to drain it through the floor wouldn't tighten down completely, allowing the hose to twist and wobble, a sure indication that it was not water tight. Simply adding a second washer, as described in another answer here, allowed me to tighten the hose sufficiently to produce a tight fit with no play between the hose and the dehumidifier. It hasn't leaked. I know it is a threads-per-inch issue, and I am stumped as to why Frigidaire would supply these units with a different thread pitch than the standard GHT (garden hose thread) 3/4" - 11.5 tpi. The threads on the unit appear to be 3/4 NPS - 14 tpi. Go figure!

Frigidaire... | Answered on Jan 13, 2019 | 29,141 views


SADLY UNLESS THE MFG HAS THEM WE DO NOT KNOW WHERE YOU WILL FIND ONE YOU MIGHT LOOK FOR A CORK AT YOUR LOCAL HOME IMPROVEMENT STORE

Dehumidifiers | Answered on Jan 08, 2019 | 74 views


Ck the fuse ,relay,freon psi wiring & compressor clutch

Danby... | Answered on Jan 07, 2019 | 83 views

Not finding what you are looking for?
Dehumidifiers Logo

Ask a Question

Usually answered in minutes!

Top Dehumidifiers Experts

Bill Long

Level 3 Expert

601 Answers

Gil Shultz

Level 3 Expert

3382 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

Are you a Dehumidifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...