Coffee Makers & Espresso Machines - Page 2 - Answered Questions & Fixed Issues

I would go on the Russel Hobbs web site and download one. https://en.russellhobbs.com/user-manuals

The top section where the blades are inserted, the grey piece, are two sections glued together. Need to separate the halves to have access to the motor, gear and electricals.

You can replace them but unlikely to repair them. The casing will come apart, with some difficulty. Remove the old switch, source an identical new switch and fit it.

It looks like the Triangle is the problem section, not that I understand why. These machine need servicing every 9 to 12 months if you use them every day. https://www.manualslib.com/manual/1069719/Gaggia-Brera.html?page=23#manual Videos https://www.google.com/search?q=Gaggia+Brera+can%27t+run+test+mode ..

https://www.google.com/search?q=capresso+c1500+pump+not+pumping+water You need a pump, or the pipes are blocked. ..

You simply have power supply board problem(PSU)

Help in the link, but it depends which model. https://www.google.com/search?q=open+the+bottom+of+my+Gevalia+coffee+maker 'open the bottom' is a rather confusing term, remove the base, remove the upper base, remove the bottom grounds tray. ..

Dead short somewhere. Check continuity from the element to the case.

Question edited for typos and spelling. It is a 'frother' rather than a 'throther'.The roaring is normal, you are releasing steam from a boiler. Steam wand issues are usually caused by cooked milk solids inside the wand. You need a good enzyme cleaner like Rinza. Help and videos in the linkhttps://www.google.com/search?q=Krups+EA+80+milk+frother+not+working+properly..

I've found if you check the basics and the obvious first it's often something silly you've missed. Is there water in the tank? Yes, I've done that. How old is the machine? Parts do wear out if it's used regularly. Are you only making one or two cups of coffee or are you making four or more cups all together? If the machine gets too hot through continuous use it will go into a "Safe" mode until it cools down. With the machine unplugged from the wall wait until it it totally cold. Open the water tank and drain as much water out as you can. At the bottom of the tank there should be a small plastic rocker arm. This is the water level switch. Use you finger and check it flops up and down. Refill the water tank and plug it back into the wall socket. Run the machine through the 'hot water Only' cycle twice. This can flush the pipes inside the machine. Let the machine cool down then put it through a Descaling cycle. Are all the spouts and nozzles clean and not clogged? Sometime a slow flow of water can cause error lights. If non of these check solve the issue it is most likely a problem with an internal part. You'll need to get a professional repairer to do the work.

The milk delivery tube is very narrow bore and in my experience you will find the tube is blocked with congealed milk solids even if you clean then regularly. You need an enzyme milk cleaner like Rinza and even with that you need to manually massage the tubes or remove the blockages. The service engineers just replace them.

That .depends on software and configuration. It is not a universal code You might find help in the manual. CIMBALI M34 SELECTRON USE AND INSTALLATION Pdf Download ' ManualsLib Inspect Electrical Supply: Ensure that the machine is receiving proper electrical power. Sometimes, an interruption in the power supply can trigger error codes. Clean Components: Check if any components related to coffee grounds or filters are dirty or clogged. Clean the underpan gasket, filter holes, and filter holder outlet hole. Coffee Ground Quality: Verify that the coffee grounds are of the correct consistency. If they are too coarse or too old, it can affect the machine's operation. Discharge System: Examine the discharge system for any blockages.

When was it last dealer serviced? These machines need a service every year. Of course they don't tell you that when you buy them! The hopper sensor needs cleaning or replacing. https://www.google.com/search?q=Delonghi+Magnifca+Evo+doesn%27t+show+%22add+beans%22 ..

Somewhere inside you should find a small rotary thermostat. Also make sure the heating element is completely clean by using a quality descaler like CLR. A lot of people use white vinegar but it is not that effective on coffee makers. Make sure the heating element under the carafe is working, because that is heating up as the coffee is brewing. ..

I yes 8t fell off Where do I get a new one?

Make sure the containers are tightly in place and check the door sensors ( the magnetic sensors may need replacing). Also, consider trying to completely power off the machine, wait a few minutes, and start it back up.

The K111 coffee maker's red light typically indicates it's in the heating process. When ready, the light may change to green. The green line with ** suggests that it's in the brewing stage. If there's no water flow through the pod and it's noisy, check if the water reservoir is properly filled and securely placed. If the issue persists, consider contacting the manufacturer's customer support for assistance.

To repair it, one must find out what the cause is. Do some fault finding first; check there is power at the switch and the motor has continuity etc. When you have found the faulty part, then you can replace the faulty part or repair the break in the cable etc.

Question edited for clarity. Question moved from Misc category. Duplicated question deleted. Refresh page to see question. Looks like the first link, although no model given. https://www.google.com/search?q=Russell+Hobbs+Uno+Uno+Pod+coffee+machine. ..

The flashing dots cannot be turned off they flash on all of Miele's products with similar displays. Do they really bother you?