Plumbing - Page 8 - Answered Questions & Fixed Issues

CLR

you either do not have it seated all the way or you have damaged an o-ring anytime you are putting togethr parts with o-rings you should make sure and put stem grease on the o-rings to ensure not to cut or damage them. if you have damaged the o-ring instead of a whole new part you can take the o-ring out take it to your local hardware store and match it with a new one. dont forget the stem grease.

Question moved from Cars and Trucks. You need to turn the water off, remove the nuts completely and wrap PTFE plumbing tape around the brass olives, about 3 wraps and then put the nuts back up and tighten them.

perhaps you have a water supply issue on hot side. Have you tried shutting of hot water angle stop valve under sink and removing supply line and opening angle stop valve to see if you have hot water?

Check the supply line and valve to see if any dirt or foreign.matter got into the line or valve when you changed out your faucet. if this is not the problem you may have a faulty faucet. You may be able to back flush the faucet with a garden hose by leaving the hot side open, but you will get wet. If you used Teflon tape on the supply line and it is a compression fitting, some of the tape could be blocking the water. for more info go to waterheaterflush.com

The classic signs that it needs a new ceramic cartridge and o-rings.

The knocking noise is caused by 'water hammer'. You need one of these.

Water Hammer Arrestors - Pipe Tubing & Fittings - The ...

https://www.homedepot.ca > ... > Pipe Tubing & Fittings Shop our selection of Water Hammer Arrestors in the section of Pipe Tubing & Fittings in the Facilities Maintenance Department at The Home Depot Canada. Rating: 3.5 · ‎31 reviews Information specific to showers https://www.google.com/search?q=water+hammer+arrestor+for+shower+valve and finally, it may be caused by the shower head. https://www.google.com/search?q=water+hammer+arrestor+shower+head ..

use an e-z out

Perhaps you don't have any. Perhaps you don't need any. WHATEVER it is you are talking about!

call kohler

No, you just have to replace with a new set.

Okay, you have black gunk in the screens of your water faucets.....This is usually found in homes with old metal galvanized water lines that have a well or Hard Water. To permenantly get rid of this problem you should have a water softener installed and replace old water lines. If you already have a water softener then you should replace all of your old metal water lines with Copper or Plastic (Plastic being the cheaper way to go). After many years of use, the inside of the galvanized metal water pipes get a Gunky Skummy Build up on the inside of the pipes from minerals and particals in the water, usually in older homes and farm houses. You will see this Gunk if you take a section of water line apart and look in it. There is no really Cheap fix for this, But if you and a Partner a fairly handy, you can do it yourself with CPVC Plastic pipe and Glue. By doing it yourself you will save alot of money on the cost of labor. If you can afford it, Hire it out to your local handyman or plumber. After replacing the water lines you should no longer get the Gunk build up and may even notice a bit more water pressure....I hope this helps in assisting you to the solution......Joe

I have no experience with modern quarter-turn taps as I prefer the ease and economy of traditional tap washers. I do have lots of experience with O rings of various types. Most commonly O ring breakage is due to the wrong size being used - diameter and/or section. when machined metal parts are fitted together and sealed with an O ring the clearance between the parts is very small - just enough to allow a sliding fit. The O ring(s) generally locate in a groove, sometimes on the end face but mostly around the diameter. O ring sizes are chosen to completely fill grooves on the end face without either stretching or compressing the rubber. Grooves around the diameter require similar consideration though some stretching is needed to assemble them; once fitted the rubber should not be under either tension or compression. The chosen section of the ring will allow the groove to be filled when the components are fitted together therefore when they are separated it will seem the O ring is too thin for the groove. If the correct size is used with carefully machined components and suitable lubrication applied during assembly there should be no difficulty. O rings are available in a number of different materials from soft natural rubbers to fairly hard synthetic materials. I suggest you carefully measure the components and compare your results with the supplied O rings.

bad storage tank or check valve ,you may be have water running back down well. or a bad pressure switch. You should have a pressure gauge on tank or line is it holding steady or falling or keep rising every time pump runs.

A Basin spanner will do it

Newer faucets are made to save water by having restrictors in them. Some can be removed, some can't. Phone the maker.

Air locks are a common occurrence after a drain and refill. An air pocket gets trapped right in the pump volute, where the impeller is housed. So, the impeller sits in a pocket of air. It will spin there all day long, or until the cows come home, if they ever do? And you will never have water movement. anyway, what needs to happen, is that air pocket needs to be pushed out of there! And the atmospheric pressure on the water in the tub will be your friend. If you have isolation valves before and after your equipment, close the valve on the discharge side of the pump. Leave the suction side valve open. loosen the union a couple of turns, on the discharge side of the pump, or one of the unions at the heater assembly, it doesn't matter which of the three. You will get water, then the HISS of Air! Let all the air come out, then water again, for about 3-5 seconds, then tighten. Open the closed valve. Start system. It should take off. Good luck.

try a plumbing store

Your Glacier Bay unit will have to be disassembled to find the failure cause which could be defective seals or a defective stem. Once the cause has been determined, you can take the defective part(s) to a hardware store or "big box" retailer to obtain replacements.

Contact delta they will have that information