Building Materials - Answered Questions & Fixed Issues


Check to see if you have anything blocking the sensors. Then try pressing the door opener to open and close the garage door. See if that resets it and stops the issue.

Building... | Answered Yesterday | 19 views


Most garage openers have a reprogram button on the lift motor. You push the button on the motor and enter in the new code on the keypad but you only have a really short time to set it so get someone to push the button from a safety ladder and you can set the code. You hit program and then push your code numbers.

Building... | Answered on Mar 12, 2019 | 25 views


They are made by Chamberlain, give them a call.

Building... | Answered on Mar 10, 2019 | 16 views


Sir one question ask me
Sir . winner rolex ad Dayton1992 78488 how much indian price

Building... | Answered on Mar 10, 2019 | 17 views


you replace it

Building... | Answered on Mar 10, 2019 | 25 views


If you use LED lightbulbs close to the operator, they can block your remote signal.

Building... | Answered on Mar 10, 2019 | 20 views


Try this link:
https://www.youtube.com/watch?v=f7S6XOOLF8g

Building... | Answered on Mar 08, 2019 | 21 views


The first step would be disconnecting the opener from the door by pulling the red emergency release cord. Lift the door half way open (manually). It should sit right where it is. If your torsion springs are set too hot the door will drift up and will be hard to get closed (by hand). That would explain your opener working extra hard to push the door down.

You could also have the perimeter seals installed too tight, or possibly an obstruction in the tracks. Even cold weather (ice) getting between the joints of the door during operation can cause that. Finally, tracks that are misaligned or bent especially around the curved radius.

Building... | Answered on Mar 07, 2019 | 4,311 views


If you're having to hold that inside button down to bring it down that is because of your sensors being out of alignment. On the bottom left and bottom right of your garage door track are your photo eyes and if they're not cleaned and pointing toward each other, then they will not allow the door to close. It will only close with the inside button because it is hardwired and when you hold the button down it shoots a continuous current that bypasses Those sensors. Remotes and keypad are wireless and must have photo sensors aligned to work

Building... | Answered on Mar 14, 2019 | 74 views


Where the wires go into the operator head you need to find a button that he has an LED light next to it. It should say learn or learn code. Press and hold that button for 10 to 15 seconds Max usually, that should do it. You tap the button to program up the remotes and you hold the button to delete the remotes. Word of advice, it deletes every remote, keyless entry or vehicle that is programmed to at that time. Nothing will work after you hold that button down until you reprogram them in again giving them a new code. To reprogram, tap the button, do not hold the button and then tap remote control button that you want to program until the motor engages

Building... | Answered on Mar 02, 2019 | 30 views


You don't, they are not compatible. You will need to find one with wires.

Building... | Answered on Mar 01, 2019 | 41 views


call for service the door lift springs are not working. Do not attempt to tight torsion tube springs. If you do be sure you have good medical coverage as these springs when wound have tremendous tension on them.

Building... | Answered on Feb 25, 2019 | 24 views

Not finding what you are looking for?
Building Materials Logo

Ask a Question

Usually answered in minutes!

Top Building Materials Experts

Lawrence Oravetz

Level 3 Expert

10524 Answers

Tom Chichester

Level 3 Expert

50916 Answers

ray gallant

Level 3 Expert

60310 Answers

Are you a Building Material Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...