Blenders - Answered Questions & Fixed Issues


The blade assembly is not being locked onto the base of the container. Check the instructions for the correct procedure.

Cuisinart... | Answered on Mar 21, 2019 | 20 views


It will probably just need the pot replacing, take note of where the wires go. I see someone else here is doing the same job and wants to know where to put them back. Take a photo first saves a lot of grief. The pot is the rotary resistance switch behind the knob.

Vitamix 5000... | Answered on Mar 01, 2019 | 968 views


Hi there. I know you were looking for an answer 5 months ago. I didn't see the correct procedure listed. My speed control just bit the dust. Anyway, here goes: Pull off the rubber cover where the container sits. You'll see 4 phillips screws, unscrew them (you can leave them in place). Next, on the black drive wheel in the center, look to find a small triangle molded into the outside of the ring. Line it up with a small slotted opening just under the drive wheel. Use a small allen wrench which fits in and unscrews a set screw. You can lift off the drive wheel. Now you have to pull the top off. On mine, it took some time as I was trying to be careful not to break anything. With persistence the top will separate from the base. My super 5000 has a 2 wire speed control knob. Hope this helps if you haven't gotten an answer elsewhere or taken it to the shop.

Vitamix Super... | Answered on Feb 27, 2019 | 5,518 views


TRY SOAKING IN HOT WATER

Blenders | Answered on Feb 21, 2019 | 32 views


At least on Amazon, the customer reviews are not so good ... only a 3.1 out of 5 for 38 reviews. Some of the poor ratings are that the unit just stopped working or a plastic housing part broke. You may have blown the motor. If it is still under warranty, and you have the receipt, you might consider shipping it back to Cuisinart ... but you pay for the shipping

Cuisinart... | Answered on Feb 19, 2019 | 42 views


ACTUALLY WE HAVE NO IDEA ASK GOOGLE

Blenders | Answered on Feb 09, 2019 | 40 views


THEY WILL IF YOU NEVER USE IT .

Blenders | Answered on Feb 09, 2019 | 32 views


are talking the blade inside the canister if so it unscrews from the clear handle and view area. otherwise if you mean the chuck below when the canister is lifted off that is held on by a fastener right in the middle dead center

Russell Hobbs... | Answered on Feb 08, 2019 | 85 views


sadly we can not help you find one , check with manufacturer or look for a rubber stopper at local home improvement store

Blenders | Answered on Feb 07, 2019 | 42 views


Check the black driving clutch on the top of the motor that engages with the other clutch half on the base of the blender jug. The fault should be there, normally it will be the motor part.

Vitamix Blenders | Answered on Feb 03, 2019 | 122 views


There's not enough detail to help solve your issue. Can you please post the brand name and model number?

Blenders | Answered on Feb 02, 2019 | 44 views


Call 1-888-367-7373
Business Hours: Mon - Fri 10:00am - 5:00pm EST

Or email: help@myproduct.care

Blenders | Answered on Feb 02, 2019 | 36 views


Yes, I know what it is. On the base of the blender jar (the plastic base) there are some "fingers" that must contact the base to allow operation to take place. Turn it upside down and look at the little plastic "fingers" around the outside periphery of the plastic base.

These fingers tend to break over time... mine only has two left right now, and it only works in one particular position as a result.

Rotate the blender jar one spot at a time until you are able to operate it "normally". I use it for margaritas, and it won't allow me to push the button for Frozen Drink unless the jar is in the right position.

I am going to try and find a replacement base (or entire blender jar) somewhere... or else I will finally have to retire my favorite blender of all time!

Oster 6700 Work... | Answered on Feb 01, 2019 | 1,710 views


GE would be a possible source.

GE Blenders | Answered on Jan 23, 2019 | 42 views

Not finding what you are looking for?
Blenders Logo

Ask a Question

Usually answered in minutes!

Top Blenders Experts

eyecam

Level 2 Expert

96 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

Ross Keen

Level 3 Expert

1337 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...