An oven bag is a very useful kitchen tool for many kinds of food. The most common is meat. For example chicken comes out tender and tasty, without drying in the process. But you can use an oven bag also to make vegetables, fish and many other kinds of food that come out better when their own moisture stays in the bag.
For my 20 year old Moen 1222, I found the outer O-ring supplied with the OEM part was slightly too large to overcome the beveled brass edge near where the key fits. I reused the old, failed part's O-ring and it went in fine. If you do this method, you should check for leaks prior to restoring. I find Moen is not my preferred supplier of choice for plumbing fixtures.
It is difficult to answer without FULL 'make model (what it is)'. These projection clocks work in the same principle, but in two ways. The time is on a LCD film and light is shone through it, then through a lens and projected onto the ceiling. The projection light can be done in two ways;
A white LED illumination light and a red LED light that comes on via an electronic timer, say 5 minutes white and then red constant
or a single LED what is white or red depending on the voltage supplied to this variable voltage LED.
The only way to fix it would be to send it for repair as it is an electronic fault You could however check the manual in case there is a setting to turn off the Red LED. I had a CD Alarm Clock Radio and the projector was the first thing to fail followed by the rest of it 3 years later. I wasn't that worried as I won it in a charity raffle. My GE Alarm Clock Radio is still going strong 48 years later!
Google
make model manual
..
Question moved from Vacuums.
If the pictures here are correct, there are 'variations' to the 1225 cartridge. No, it doesn't sound as though yours if fitted correctly. There is normally a stop on both sides of hot and cold to stop it spinning 360'.
https://www.google.com/search?q=1225+moen+cartridge
Question edited for clarity.
Questioned moved from Misc to clocks.
All questions need full 'make model (what it is)' as the first three words or it is all guesswork.
My guess is that you are in the wrong time zone and it will change in 2 weeks when it changes in the UK. You are set to GMT instead of PST, CT or EST.
..
You can't. What this means is that the seal between the panes has broken down, and every time the window heats up (in the sun) air is expelled, and when it cools, air is drawn in, with moisture to boot. You will always have that issue. However, you can have replacement units made up that will fit into the existing window frame. Any good glazing company will be able to get a double glazed unit made up to fit into the existing window.
Question edited for clarity.
Question moved to a better Category.
Get out your digital test meter and check the switch for continuity and operation. If that passes the tests, follow the wires and look for a relay that operates the pump. Also test the pump motor for resistance.
https://www.google.com/search?q=aqualux+whirlpool+bathtub+not+working
..
There are a few potential reasons why your Bulova B1987 mantel clock has stopped chiming:
Check if the chime switch is in the "on" position. If it is not, switch it to "on".
Make sure that the clock is wound fully. A clock that is not fully wound will not chime.
Check if the chime melody selector is in the "off" position. If it is, move it to a melody position.
If the clock has been moved or bumped recently, the chime hammers may have been knocked out of alignment. This can be fixed by a professional clock repair person.
The chime rods or hammers may be damaged or worn out. This can also be fixed by a professional clock repair person.
If none of these solutions work, it may be best to contact a professional clock repair person for assistance in fixing the clock's chime.
Before deleting the current program and reprogramming your NX-8 wireless smoke detector, you may want to try the following troubleshooting steps:
Check the batteries: Ensure that the batteries in your wireless smoke detector are not dead or low. Replace the batteries if necessary.
Check the signal strength: Make sure that the wireless smoke detector is within range of the NX-8 control panel. You can try moving the detector closer to the panel to see if it helps.
Check for interference: Interference from other wireless devices, metal objects, or thick walls can affect the signal strength. Try removing any potential sources of interference or relocating the detector.
If these steps do not resolve the issue, then deleting the current program and reprogramming the wireless smoke detector may be the next step. Be sure to follow the instructions in the NX-8 programming guide to properly delete and reprogram the detector. If you are not comfortable with programming the system yourself, you may want to contact a professional alarm company or technician for assistance.
