Vehicle Parts & Accessories - Page 8 - Answered Questions & Fixed Issues
Free engine diagram for 96 5.7 vortec
https://images.search.yahoo.com/search/images;_ylt=AwrFeFQIGjdjVukCKDqJzbkF;_ylu=c2VjA3NlYXJjaARzbGsDYnV0dG9u;_ylc=X1MDOTYwNjI4NTcEX3IDMgRmcgNtY2FmZWUEZnIyA3A6cyx2OmksbTpzYi10b3AEZ3ByaWQDWnJyN0wwVEpRSHlNOURLRnppMm95QQRuX3JzbHQDMARuX3N1Z2cDMQRvcmlnaW4DaW1hZ2VzLnNlYXJjaC55YWhvby5jb20EcG9zAzAEcHFzdHIDBHBxc3RybAMwBHFzdHJsAzMxBHF1ZXJ5A0NoZXZ5JTIwMzUwJTIwdm9ydGV4JTIwRW5naW5lJTIwRGlhZ3JhbQR0X3N0bXADMTY2NDU1NTg4NQ--?p=Chevy+350+vortex+Engine+Diagram&fr=mcafee&fr2=p%3As%2Cv%3Ai%2Cm%3Asb-top&ei=UTF-8&x=wrt&type=E211US1494G0
9/30/2022 5:18:20 PM •
Engines &...
•
Answered
on Sep 30, 2022
•
1,070 views
How to reset automatic sliding door on chevy venture van
The rear side door actuator control modules monitor the power sliding door positions at all times. Whenever the battery positive voltage supply to a rear side door actuator control module has been removed or the on-board diagnostics have been activated the power sliding door system(s) must be re-initialized. Re-initialize the right or left power sliding door systems using the following steps:
- Turn the ON/OFF switch for the power sliding door system to be re-initialized to the OFF position.
- Manually open the power sliding door completely.
- Manually close and latch the power sliding door.
- Turn the power sliding door ON/OFF switch to the ON position.
- Open the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch.
- Close the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch.
9/9/2022 4:43:40 AM •
Chevrolet...
•
Answered
on Sep 09, 2022
•
7,270 views
P2440 trouble code
What Does the P2440 Code Mean? Diagnostic trouble code (DTC) P2440 stands for "Secondary Air Injection System Switching Valve Stuck Open." The secondary air-injection system pumps fresh air into the exhaust system to help burn exhaust emissions as the engine warms up.Mar 1, 2022
Remote start work but door will not unlock or lock!
Do the doors unlock when the remote starter is not running? If so, then you to connect to a different set of door lock wires.I usually connect to the factory alarm and disarm wires in the driver kick panel. They are blue for arm and pink for disarm. You test them by turning the key in the drivers door.
8/18/2022 8:12:44 AM •
991 Responder...
•
Answered
on Aug 18, 2022
•
8,811 views
Passlock II issues for 99 Tahoe
turn key to start position for 10 minutes and it will reset passlock
Or, once you're tired of being stranded for 10 min every 6 weeks or so, try the following:
Here's the "fix" I did for my 99 tahoe. Took the cover off the
steering column, unplugged the sensor from the cylinder *while* the car
was running. it's a 3 wire plug red w/ white, orange w/black and
yellow. From then on, the car will always start and ignore the sensor.
The only negative is the security light stays on. Replacing the BCM only postpones it from happening
again if the problem is the resistance in the ignition lock cylinder. Check out the following links. Good luck.
http://car.justanswer.com/for/ce07-bypass-lock-sensor-1998-chevy-tahoe
http://general-motors.pissedconsumer.com/gm-passlock-ii-system-has-major-inherent-design-flaws-20080502119601.html
Not finding what you are looking for?