Brother printer ink cartridge chips
Unlike the inferior Epson cartridges, the Brother printer resets the chip when you refill them.
Follow the installation of fresh cartridge instructions.
I have a Brother Lock Serger. 1034D The Pressure foot Lever just spins around.
If you can remove the cover on the left side you will see the presser foot bar. On the bar there will be a screw that may be loose. Turn the handwheel until the needle is all the way down and lift the foot manually until just before it makes contact with the needle clamp and tighten the screw on the presser foot bar.
That should do it.
Have brother dcp l2540dw laser printer will print from computer but will not make copies pl help
Could the DCP-L2540DW be waiting for another page to be scanned for a two-sided document? If it is set for manually copying both sides of a page that is on the scanner glass, press 2 or the down arrow to get the copy to print. See the basic user guide available here:
https://support.brother.com/g/b/manualtop.aspx?c=us&lang=en&prod=dcpl2540dw_us_as to find the section to set the copy function to turn off the two-sided option.
If the LCD screen says "out of memory", you need to get faxes and other print jobs out of memory or turn off memory receive. If the LCD screen shows "scan unable", then the scanner mechanism may not be moving properly. Try turning the all-in-one off and unplugging it for a while. If the mechanism is still stuck when the power is connected again, then the unit needs to be repaired or replaced. If it is under warranty (1 year unless you bought the extended protection), contact Brother.
Cindy Wells
I have the Brother LS2300 and when I push the pedal to begin sewing it tangles and becomes unthreaded
This is most likely a threading or a tension issue. Take out both the top and bottom threads. Clean all the areas you can get to, top and bottom, to remove any tiny pieces of thread and fluff. You'll be surprised how much trouble two or three little bits of old thread can cause. Re-thread the machine and check your tension settings.
Are you using a different type/brand of thread, have you changed the needle or are you sewing a different type of fabric? These can all affect how a machine sews so you might need to adjust your tension settings.
I have continued looping on bottom. Brother SE 1900
Have you tried adjusting the bobbin tension? There's a small screw on the bobbin case so the bobbin can be adjusted. only turn the screw a little at a time. Also be sure your top tension isok. However if you still need help these days you can buy a new bobbin case and a new top tension, both will be adjusted already to use from the factory. don't let it drive you crazy they sell the preadjusted parts for us few that just want to sew not be a tech to just sew a blouse etc. I hope this helps. good luck
Lynn
My dog ran past the foot controller and jerked the cord out. Now it reads an error F04 Foot controller breaker. I have tried a different foot controller and still shows the error. Can I fix this?
The error message F04 Foot Controller Breaker likely indicates that the foot controller has shorted out or is no longer functioning properly. Depending on the device you are using, it may be possible to repair it yourself, but in many cases, you will need to send it to the manufacturer for repair or replacement.
If you have tried using a different foot controller and are still seeing the error message, it is possible that the problem is with the device itself, rather than the foot controller. You may want to check the wiring and connections for any visible damage, and make sure that all cables are properly connected and secure.
If you are unable to resolve the issue yourself, it may be best to contact the manufacturer for further assistance. They may be able to provide additional troubleshooting steps or information on how to obtain a repair or replacement.
Brother 8510 Faded image ?
If you have replaced multiple components in your Brother 8510 printer, including the oven unit, laser unit, high voltage board, power board, and drum unit, but are still experiencing faded images, there are a few other potential causes and solutions to consider:
1. Toner Cartridge: Ensure that you are using a genuine and compatible toner cartridge for your Brother 8510. Low-quality or incompatible toner cartridges can result in poor print quality. Try replacing the toner cartridge with a new, genuine Brother cartridge to see if it resolves the issue.
2. Toner Density Settings: Check the toner density settings in the printer's software or control panel. If the density is set too low, it can result in faded or light printouts. Increase the toner density setting to see if it improves the print quality.
3. Cleaning the Corona Wire: The corona wire is responsible for transferring the toner to the paper. If it is dirty or contaminated, it can cause faded prints. Consult your printer's manual for instructions on how to clean the corona wire properly. Be careful when handling the corona wire as it is delicate.
4. Print Settings: Check the print settings on your computer or within the printer's software. Ensure that you are using the appropriate print quality settings and that any power-saving modes are disabled. Adjusting the print settings to a higher quality mode can enhance the print quality.
5. Contact Brother Support: If you have exhausted all the troubleshooting steps and the issue persists, it may be beneficial to reach out to Brother customer support or a qualified printer technician. They can provide further guidance or arrange for a professional inspection and repair of your printer.
Remember to follow the manufacturer's guidelines and safety precautions when working with printers and their components.
Brother p touch 1005 new batteries inserted won't turn on
Has not been used in a while but nothing, new batteries new tape, used the eleIf your Brother P-Touch 1005 label printer won't turn on after installing new batteries, there are several possible solutions you can try:
- Check the battery installation: Make sure that the batteries are inserted correctly, with the correct polarity. If the batteries are not inserted correctly, this can cause the device not to turn on.
- Clean the battery compartment: Dirt and debris can build up in the battery compartment, which can prevent the device from turning on. Clean the battery compartment and make sure that the battery contacts are clean and free from debris.
- Use a different power source: Try using the AC adapter that came with the device to see if it will turn on when plugged into an electrical outlet.
- Factory Reset: Hold down the "Frame" button while you insert the batteries to perform a factory reset on the device.
- Contact Brother Support: If none of these solutions work, the issue may be with the device itself and you may need to contact Brother support for further assistance.
It is important to follow the manufacturer's instructions and guidelines when attempting to troubleshoot any issues with the devic
ctric wire nothing
Brother XL5600 is not stitching properly and dropping stitches?
need to check the hook timing.
put it in zig zag, no fabric, turn the hand wheel to you slowly.
check the needle when it is coming back up, is the hook picking up the thread? if yes continue to check the next side, so if you check the left side then check the right. if any side its not picking up the thread then the timing is off and need to be retimed
Not finding what you are looking for?