Bose Audio Players & Recorders - Page 9 - Recent Questions, Troubleshooting & Support
How to make a 15 pin female sound in cable
Ya, here is a diagram I made of my Acoustimass 10 IV input cable. All you need is a female 15-pin d-type connector and a bunch of speaker cable (also one RCA connector for sub connection). Here's my diagram:
My sound in cable was missplase and can i make it
Here's a diagram of the 15-pin serial input cable that came with my Acoustimass 10 IV system. You just need a 15-pin female d-type connector, one RCA connector and a lot of speaker wire. Here's my diagram:
Bose Cinemate Sr1 volume keeps auto turning off when not in use
Hi, All. First, thank you for suggestions posted. Next, I have unplugged both the subwoofer and the center channel speaker, left them unplugged for a minute or two, then re-plugged them in. However this did not correct the problem for me. When I pause the television for five or 10 minutes for example, the Bose volume automatically shuts off. This is a major inconvenience. I suppose if nobody can address this issue with the remedy here, I shall have to call Bose and see if they can assist. Any other ideas or suggestions? Meanwhile thank you very much.
Control Pod for Bose Companion 5 speaker system
I had the same problem right out of the gate, the volume dial on my control pod for my Companion 5 wasn't working, however, the touch pad and LED worked. I called Bose customer service and was instructed to:
First, unplug the power directly at the back of the woofer while the unit was on;
Next, I was instructed to unplug the control pod, visually inspect for any damage/defect;
Finally, re-seat the control pod on the back of the woofer and then lastly plug the power cable back into the woofer.
It worked like a charm. I hope this is helpful!
How can i hook up my 30gb Ipod to my Bose 901
There has to be some amplification in here somewhere. Any single amplifier will not work correctly with the Active EQ for 901's applied to non-901 speakers.
Any MP3-player device with at least a headphone output can feed any standard audio device that has a Line Level input (other than "PHONO") once the output is adapted to fit the input.
Bose IPod Docking Station Remote not working
I had the same problem. Very frustrating. Tried everything. Discovered the solution. The device that the remote control sends a signal to is located inside the grill of the SoundDock. The receiving device has a lens (which we can't see since it is hidden inside the grill). It can get dust on it that interferes in the signal being received and the remote can then only adjust the volume up and down but no other feature. I sprayed my grill with a can of air. Not being sure exactly where the device is, I sprayed the entire grill, being careful to spray from six inches or so from the grill. Just like that - the remote then was immediaely fully functional and I have ever since been able to use all of the remote's functions. Steve
Button on bose speaker stuck
The buttons on my Series-II cubes get stuck all the time. It seems the button itself sticks against the housing. I first spray on a little bit of silicone to coat the sides of the housing that rub up against the button. Then I use a straight razor blade to pry in the gap between the button and the wiring-holes, alternating below each hole. As you do that, the button rocks out a little bit at a time.
How to hook a 28060 2y920 Bose amp up
https://www.google.com/search?q=manual++hook+a+28060+2y920+Bose+amp+up&client=opera&hs=Wvw&tbm=isch&source=iu&ictx=1&fir=yJ_vTqFCh0gA2M%253A%252CcGQ5axQMAztfOM%252C_&vet=1&usg=AI4_-kQ3jFP_7kiR3DW0lKR4qtrqElJlgg&sa=X&ved=2ahUKEwj3n8KcmsLoAhUGy4UKHS_IBcQQ9QEwBXoECAkQCw#imgrc=yJ_vTqFCh0gA2M:
Creative Inspire 5300 Volume Control broken!
For those searching the answer "How to replace/repair Creative Inspire 5300 volume control":Its simple : looking at the back of the suboofer, the pins are as follows from top right, clockwise : LED VDD , Balance pot middle leg, GND, pots + legs, Volume pot middle leg, on switch input. Connect one pots ends to GND and the other ends to pots +, connect a switch on GND and on switch input, anode of led to LED VDD, cathode to GND (there is a 1,8k resistor inside so no external resistor needed)
Not finding what you are looking for?