Bosch Dishwashers - Page 6 - Recent Questions, Troubleshooting & Support

shut off power you have a short or motor failing

check link below, press the helpful button Dishwasher Making Noise Bosch Dishwasher Circulation Pump Replacement Part...

Hello Deepak,

You can definitely fix this yourself, but I'm not entirely sure from your description which part is "dropping off". It may be a simple fix where something needs to be clipped back into place or you may need to replace something. Please can you take a look at the images below and identify which part you are having trouble with.

Below is the back of the upper spray arm which clips on to the upper rack. It has a grey plastic cover behind which is a large white plastic washer / gasket. The washer simply slots in to the back of the spray arm and the grey cover clips in over the top.

Your description suggests the grey plastic cover and/or the white washer are dropping off. If the grey plastic cover is missing, it may have fallen into the bottom of the washer under the lower rack, in which case you should be able to find it and clip it back on. If it's missing or wont clip back on, you will need to replace the upper spray arm as the cover and washer are not available separately.



This is the water delivery tube which clips to the back wall of the washing compartment. There is a metal clip which secures the tube to the wall. The open hole and one of the spigots slot in to the two holes in the back of the upper spray arm above. The spigot used depends on which height setting the upper rack is on.



Basically, everything simply clips together. If nothing is broken, you should be able to fix this at no cost by simply clipping the offending part back into place.

Hope this helps. If you need further assistance or help locating replacement parts, please let me know what needs to be replaced. Nearly all Bosch parts are available and in stock direct from Bosch.

Regards,
BElectric

Check that the new panel isn't pushing down on any of the buttons when you reassemble it. Compare it with the old panel and look closely for any differences. Ive come across it a few times where changes to panels have been made and its supplied to fit yours but the changes prevent correct operation. You may have to file or cut any part off which interferes with the switches or controls. This happens when there are production line changes on the same models.

If their is water at the bottom it's probably the water pump

Hot water, not boiling, get a rag, soak it and cover lid. Let it cool before having another go at undoing. Top tip, try to tighten, just a bit, as quite often it will go that way!

I had the same problem with my Bosch dishwasher.I came to this web site to find out how to get the door off.I took the experts advice,placed 4 pillows on the floor in fromt,opened the door,took out the screws and the front panel dropped down.It was so easy,the plastic spacers stayed in place.I put a little J B weld on the handle screws and tighted the handle and put everything back together,12 minutes tops.Thanks for the help,thankful in Georgia

Humming noise is an indication of your drain motor getting power but not spinning. Either your drain pump is defective and needs to be replaced, or something is stuck in the pump preventing it from draining out the water. Either way you will have to take the dishwasher out and get at the pump from the bottom of the machine.

A high-pitched sound which occurs when filling is usually cavitation - air in the water valve causes a kind of "squeal". It's relatively harmless, but can be annoying. You may need a new inlet valve. But first just try detaching and re-attaching the hoses to the valve. Sometimes that's enough to fix it.

Pour boiling water over the cap and with a cloth unscrew whilt still hot.

possibly a dead control board

first find source of leak --valve -water line --door gasket --pump --drain --drain seal

More than likely the hinges will adjust as they may have been bent.

Check the water level.

sorry no clue as we do ours the old fashioned way by HAND

It appears that your model is probably SHEM63W52N/01 Bosch cunningly hide the heater inside the pump housing and sell the pump and heater as one unit! Having said that, the heater usually works or it doesn't. When it comes on is controlled by a control unit, another expensive part. I was looking for a relay, but there isn't one. The spray arms move by the water pressure making them spin. First of all I would remove them and check all the holes for blockages. Replace them and make sure they spin well by hand. If you are inclined, strip the pump and make sure is is clear of blockages and the impeller spins well. Check the continuity of the heater element. https://www.appliancepartspros.com/parts-for-bosch-shem63w52n-01.html ..

Check the spinner is not blocked or jammed.

These handles are often mounted from the back of the door. You might have to strip down the whole door to replace the old handle

It means that the dishwasher is not draining properly due to the drain filter being blocked

1. Defective cycle timer 2. Defective door interlock wiring or latch