Bosch Dishwashers - Page 3 - Recent Questions, Troubleshooting & Support


Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually is with the control...unfortunately. This is
likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg

The culprit will 99% of the times be one of the pins from the heater relay,hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...this can also manifest as a long cycle time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning, no heating ( don't be fooled by the homes inlet hot water temperature ) as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e. ( this may differ from your specific model, but the same rules apply )

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last.
Bosch recommend`s replacing the control and I don`t pretend to speak on their behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**

Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness. Good luck.

Regards,

Macmarkus :)

Bosch... | Answered on May 07, 2019


Most late dishwashers range between 40 and 50 dB. That is equivalent to the ambiant noise of a library room.

Bosch... | Answered on May 02, 2019


Frigidaire dishwashers can lose their pump prime and will not fill with water if there is no priming water in the bottom of the unit. To solve this, add several quarts of water to the unit. Let it settle down in the bottom until it stops going down. Start the washer and you will hear this water pump out of the drain and the unit will now fill with fresh water.

Bosch 18 in.... | Answered on Apr 13, 2019


It may just be the way you are loading the machine.  If the dishes are not allowing the the detergent door to open fully, the tablet sits in the dispenser until you open the dishwasher, letting the dispenser door open and the half dissolved tablet falls out!     Try being more careful how you load the machine or just chuck the tablet in the bottom of the machine instead of the dispenser!

Bosch 24 in.... | Answered on Apr 13, 2019


FIXYA has no idea where or if the mfg makes or sells replacement wheels . suggest you go see a dealer of product and have them check for you .

Bosch... | Answered on Apr 13, 2019


PERHAPS GLUE OR POP RIVETS . I HAVE NOT SEEN IT

Bosch... | Answered on Apr 07, 2019


Try cleaning the pressure chamber and sump hose, if not this , it is not heating ( heater or pcb)

Bosch... | Answered on Apr 03, 2019


The cycle timer may be defective.

Bosch... | Answered on Mar 31, 2019


Many owners of the Bosch dishwashers perceive h01 (h: 01) or h02 (h: 02) and other signs as an error. But in fact, this is not an error, and you accidentally got into the start-up timer menu (delayed start of washing dishes). In this case, h01 means that washing dishes will start exactly in 1 hour; if the display shows h02, then washing process will begin exactly in 2 hours. As a rule, in most models of dishwashers from Bosch, a delayed start can be set in the range from 1 to 24 hours.
Read more at https://bosch-dishwasher-errors.com/bosch-dishwasher-error-code-h01-h02/#uGUAe8vpcVfLM3YX.99

Bosch... | Answered on Mar 19, 2019

Not finding what you are looking for?
Bosch Logo

7,036 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...