Blakeslee Food Mixers - Page 4 - Recent Questions, Troubleshooting & Support

Unfortunately not available anywhere online. Check eBay once every couple of weeks. https://www.google.com/search?q=Cooks+sm248+manual ..

Question edited for full 'make model (what it is)'. There must be a spring in the base that helps the top rise when you depress the button. You will need to remove the base. The manual doesn't mention anything and there is no Service Manual https://www.manualslib.com/manual/1021018/Hamilton-Beach-63390.html?page=5#manual Very limited help here apart from JustAnswer dot com https://www.google.com/search?q=hamilton+beach+model+63390+mixer+tilt+button+not+working ..

Hi, apply some cooking oil to where the parts are connected. If that fails, please submerge the parts in a bucket of or tube of water and attempt to detach them from each other. If all else fails, please reference the manual to ensure that you've not missed a detachment procedure. Thank you.

Hi, The mixer looks to be an antique so you might start with Ebay to find that specific mixer part. Thank you.

The sparks are generally seen where the carbon brushes meet the copper commutator on the motor spindle. This is actually fairly normal. You can lessen it by spraying with some light machine oil, but eventually you will need to replace the carbon brushes.

Impossible to guess what make and model you have! Google make model replacement beater https://www.google.com/search?q=Moulinex+model+replacement+beater ..

Hi, If you call the glue manufacturers, they might be able to direct you to a substance that can dissolve the glue that was applied. Thank you.

There is a little spring clip where the beater is inserted. Disasemble and use some pliers or such like to gently squeeze the clip closed a little. Be careful not to close it up too much.

Question edited for clarity, two question made into one. Duplicated post deleted. Refresh the page to see your question published. Turn the mixer upside down and spray WD40 into the beater holder holes. I think there is a ball bearing detent that hold the beaters and it is probably seized. Leave for a couple of hours and spray again for another couple of hours. https://www.google.com/search?q=Hamilton+Beach+025+HB+10+speed ..

Question edited for clarity. Unit has two maker badges. Any place that services Hobart Mixers will service yours https://www.google.com/search?q=hobart+mixer+service+london+england A.S. Catering seem to be the sales agent for them. https://www.google.com/search?q=22HI-B%20service ..

I expect 4 years later, you managed how to do it :>D Your post attracted spam which was removed, so it brought your question back to the top. It is a pity Chef Andrew didn't see it then! Spray all around the gap between bowl and base with WD40. Then use brute force. Next time, rub a little Vaseline around the surfaces that lock the bowl in place.

When your Grundig start flashing it's 99% stop position switch fault. It can be located in opposite side of speed control board.
You can simply open your mixer, remove speed control board and inject contact cleaner (or similar) directly to holes od black switch. I used medical injector.
Of course better solution is replace switch - it cost few dollars for ten. But in this case you can apply DIY skills. Nothing hard.

Give me the serial number,also hobart does'nt release their service manuals to the general public.However if you goto hobartcorp.com type in your model which is a d300 and you can access an exploded view of the parts.I work for hobart and service these mixers often.Any questions let me know.

Take a 4 foot length of string and put it through the loops of the stuck beater. Tie the end of the string in a knot. Put the loop of string under your foot and hold the body of the mixer and pull.

BIN IT AND BUY THE BEST YOU CAN AFFORD

Make and model may help you get an answer.

Again Linda Russell... A sample Mixer MODEL NUMBER would be 100.8900890A For RED .... 100.8902890A See here: Kenmore 100 8900890A Use Care Manual I'm still not yet psychic... Help us help you for FREE Carnac the Magnificent

the part that has failed and intensionally so, is a 'shear pin'. The is a mild steel pin that breaks if the beater gets jammed or strained. They are put into a cog that slips over a shaft. You just have to strip down the planetary head or the main power shaft and find it. A KitchenAid part will fit it. https://www.google.com/search?q=bhg+stand+mixer+replacement+parts ..