AudioBahn Car Audio & Video - Recent Questions, Troubleshooting & Support

You have to wire it in 'Bridge Mode'. https://www.google.com/search?q=audiobahn+a2301Q+connect+2+subs%2C+2+speakers

The amplifier is only stable to 2 ohms.
Assuming the cubs are dual 4 ohm voicecoils - a 2 ohm load with 2 subs is not possible.
You can only wire up 1 dual 4 ohm voicecoil sub (both positives to amp... and both negatives to amp) to get a 2 ohm mono load.

Thanks for using FixYa -a 4 THUMBS rating is appreciated for answering your FREE question.

i had the same thing happen to me on my 2300hct audiobahn. it turned out to be the remote. but soon after my amp went dead. i than switched to JL no problems since.

but i still use audiobahn immortal 12's.

are you ben kerr from carlisle? I've been looking for you. txt me 07731596368. :)

i think they are if you look into them the imortal is a bad as sub. but the enternal was design to even hit note the imortal cant.... you gotta make sure you have enough power to give them justice i like the a2300hcx by audiobahn look in to that amp they are nice..

Yes audiobahn do make a QUAD coil, and some people get confused with the - - + + on the terminal, This is called a dual lug, Check out Audiobahn.com and go to tech suport. Thier you can look up the wiring diagram for this sub... TRUST ME hope this was helpful positive feed back be nice lol

search the web.

I can do it. What are the symptoms

Resistor colour codes https://www.google.com/search?q=resistor+colour+code No wiring schematic exists. No Service Manual exists. https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk01Lz55kU-L2ZSMHzvFAEs_MMAXaQw%3A1603501290257&ei=6nyTX-maD9K0ggek1bGICA&q=Audiobahn+a12001dt+wiring+schematic ..

Discuve what fuses that the amplifier is

Hello William Novelli, if it would be compatible, but you should control the order of the connections, they can vary I send you the link to download the manuals of both models and compare the connections, if you find it complex, consult a specialized technical service I hope you find it useful Regards Franco Dosil Hola William Novelli, si seria compatible, pero deberas controlar el orden de las conexiones, pueden variar Te envio el link paravque descargues los manuales de ambos modelos y compares los conexionados, si te resulta complejo, consulta con un servicio tecnico especializado Espero te resulte util Saludos Franco Dosil https://manualmachine.com/audiobahn/aeq7/18414-user-manual/ https://manualmachine.com/audiobahn/aeq8/18268-user-manual/ https://www.manualslib.com/manual/211695/Audiobahn-Aeq6q.html

do you still have it

as your sub is only rated to 400w rms simply connect the sub to either a or b channel outputs you may wish to use an rca splitter before the amp to feed both left and right audio channels into a single channel on the amp. WARNING connecting both channels on the amp to the sub will overload the sub and possibly blow it up so i highly recommend not doing so.

i was not able to locate a manual but i did find some interesting information that hopefully may help, The AudioBahn AW1000X Car Subwoofer Features: dual 4-ohm voice coils, non-pressed pulp cone, huge foam surround, frequency response 23-500 Hz, power range 50-600 watts RMS (300 watts per coil), peak power handling 1,200 watts, sensitivity 91.1 dB, top-mount depth 5-1/4" ,sealed box volume: 0.4-.95 cubic feet, ported box volume: 1.632 cubic feet.

i'd need more info but from what you've stated, sorry to break it to you but it sounds likely you've incorrectly wired you speakers and blown your amp. this will prove no doubt an expensive mistake and learning exercise.

to drop the amp load to 1 ohm you need to divide the output signal path and the best way is by wiring a second woofer in parallel as seen in the ideal diagram attached this has the desired effect of doubling the volume . since 2 ohm divided by 2 is 1 ohm load connected to your amp. so the short answer is no you can't do that with a single woofer

sounds like a thermal overheat protect issue, sorry to break it to you but sadly the way most amps are built these days it's either not worth the cost of trying to repair or impossible to do so by hand. you'd be better off just getting a new amp

Generally there are 2 parts to this problem part 1 input signal as these woofers are just subs remember to give them a low line in signal before the amp (see diagram) i like to use rca low pass crossover filters from harrison labs (see link) part 2 is the wiring configuration of the 2 woofers by wiring them in parallel as shown in the diagram you reduce them to a 2 ohm load for your 2 ohm amp meaning you'll get max loudness and efficiency Harrison Labs FMOD Inline Crossover Pair 100 Hz Low Pass RCA Shipping is...