Amana Answered Questions & Fixed Issues

blower capacitors or motor bad

you will need to call for service. if it needs freon you cannot recharge it freon is expensive and requires a license.

Sounds very similar to having something such as a sock or small article of clothing that is too large to be sucked down the drain hose into the pump. So what happens is it hangs around between the inner and outer drums and sometimes gets itself lodged over the drum drain hole, and can allow water to be centrifically flung over the top of the drum. Most times when the spin cycle stops, the article of clothing will dislodge and float around inside the drum only to do it again later....
If you can remove the top of the machine, you can usually see the gap between the two drums and use a piece of coathanger wire with a small hook on the end and "go fishing in the area between the two drums and close to the drain hole location... bet you'll find something in there... Let me know how it goes... and if I can help .. ken

I have an Amana AS12575GRB01, the cover to the light bulb on the fridge side is mounted on the top inside back right corner. Having problems removing it

It is a gas appliance and can only be worked on by a register gas certified technician.

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking
http://www.fixya.com/support/r4033033-gas_range_repair_burners_keep_clicking

heatman101

check cogs under agitator if ok possible bad motor or belt

That is probably a door lock error. It could be that the door was not completely closed while running. A piece of clothing might be stuck in the doorway. The lock mechanism may have failed. It could also be that the lock position sensor didn't communicate properly with the washer control board. Note: if the error was 5d, that indicates "suds". Too much detergent was in the machine. Try running the washer with no clothing or detergent added. Please add a comment with the model number of your washer for a parts list/diagram. I hope this helps. Cindy Wells

This sounds like a selctor switcwh problem. A selector switch determines which of the above mentioned cycles works. Here is some basic information: https://www.partselect.com/Washer+test-switch+repair.htm

Check your lint screen and vent for restrictions or clogs. Then check the resistance for the thermistor at the control board. You need to confirm that the wiring and replacement thermistor are undamaged. Look for the white connector and test across pin 2 (blue) and pin 6 (red). If the resistance is in range, then the control board is faulty. Replace the control board. I hope this helps. Since you already replaced the thermistor, I assume you know where to find the parts list for your Amana dryer. Cindy Wells

not sure i use mine without exhaust hose

try a power rest. It that doesn't work, you need a service call as it is likely that the control board has failed. They are expensive so need professional diagnosis and warranty on the repair.

Why Your Dishwasher Isn't Working - Amana

https://www.amana.com > articles > why-your-dishwash... To do this, press either Start/Resume or Cancel, or open and close the door. Still not working? Reset it. Disconnect it from the power source for one minute. If ... ..

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

There are several videos on line about buzzzing fridges. This is one https://www.youtube.com/watch?v=O2TVZazGLJ0

To operate the unit without having the remote .. Turn the unit OFF and unplug it for 15 minutes. After the time has elapsed, plug the unit in and turn the ON/OFF Switch to ON. You should now be able to operate the controls on the unit itself. As it should have reverted back to the original factory setup settings.

Hope this helps you and thanks for choosing FixYa.

Question edited for typo 'Tanden', not 'Tamden'. Information on mainboard resetting in the link https://howtodiscuss.com/t/amana-tandem-7300-washer-3-beeps/95090 ..

copy and paste https://www.amanaparts.com/Shop-For-Parts/a4b1d693274/Model-ATB2232MRW00-Amana-Refrigerator-Parts?n=3

Self evaporating simply means there is a drain pan with a heater device installed that will evaporate and condensate that drains from the unit into the pan.

You do not need the external drain pan unless the unit makes more water than the drain pan and drain pan heater can handle.

There is a control sensor that senses the amount of water inside and the water level changing. it may be faulty causing it to stop on mid rinse or the control is positioned incorrectly you will need to contact the OEM with the issue as it sounds like a hardware problem

U wud certainly taste it if that happend. Plastic not toxic if eaten..only if burned and emits fumes