Amana Logo

Amana Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 1K Products
  • 75K Answers

Assuming unit has cooled down, unplug for 5 minutes and then plug back in. If code still flashes and door doesn’t unlock, there’s a problem with latch associated parts, the control board, or wiring between the 2.

Amana Kitchen... | 43 views | 0 helpful votes

Motor could be burning out and drawing too much power. If it's old not worth repairing.

Amana... | 88 views | 2 helpful votes

Try this link, maybe this is what your looking for

Amana Washing... | 22 views | 0 helpful votes

There should a on-off rocker switch on the icemaker. Turn it off.

Amana... | 35 views | 0 helpful votes

Always check the breakers in your electrical breaker box in house first. I say this because it takes 2 for dryers one for coils and lights the other for motor and thermostats. Next check door switch by listening for contact click sound when you push the door closed if you hear it switch is good and most likely motor is bad.

Amana Dryers | 41 views | 0 helpful votes

Once the bolt is removed, it should be able to just pull up. It may be tough but grab it from the base and pull up with some force. Carefull not to hit your face once you free it up.

Amana Washing... | 30 views | 0 helpful votes

check your wash program selection check tap on at cupboard

Amana Washing... | 45 views | 0 helpful votes

Could be switch failure or control board failure

Amana Washing... | 152 views | 0 helpful votes

Over the years I've found that if it buzzes but will only start when you "assist"it, the drive motor is at fault. The hot smell you describe backs that up.. This assumes the idler is ok and the belt is routed correctly. Make sure the belt is on the motor pulley and not riding on the motor shaft. This can happen sometimes if you have to install the belt by feel when you can't see it well . That said, the motor should still start without assistance even with an incorrectly installed belt.
Good luck

Amana Dryers | 42 views | 1 helpful votes

LO or FL error is displayed if no water is entering the washer. Check to see if water valves are turned on and check in line filter screens at inlet to hoses. "

Amana Washing... | 25 views | 0 helpful votes

I'm leaning 2 directions, one is that your tstat is sensing your heatpump can not keep up with the load. Therefore bringing on heat strips or two, you have a cycles per hour limit set for compressor heating and your machine is cycling too often.

Amana Heating &... | 31 views | 0 helpful votes

Old model refrigerator have their defrost timer located at the back right upper corner or the left lower corner with a hole slot for a screw driver. New models have it inside the refrigerator near the thermostat control. It also has a hole slot for a screw driver.

Amana... | 51 views | 0 helpful votes

Does the lid lock? Also Could be the motor. Also could be the actuator that shifts transmission from agitate to spin. Also could be belt issue. Or maybe something wedged between inner and outer tubs. Call a professional unless you’re comfortable with checking all this out.

Amana Washing... | 51 views | 0 helpful votes

Find what the error code relates to and fix it. Then the code will go away when you reconnect to power.

Amana Washing... | 42 views | 0 helpful votes

Clean the filter and try it again

Amana Heating &... | 41 views | 0 helpful votes

Possibly thermal fuse is bad. Or maybe door switch.

Amana Dryers | 42 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Amana Experts


Level 3 Expert

84524 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Cindy Wells

Level 3 Expert

5829 Answers

Are you an Amana Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides