Amana Dishwashers - Page 8 - Popular Questions, Answers, Tips & Manuals

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes


' ' ';

Hi


Thanks for using FixYa. This issue can be either due to a faulty door latch or door lock switch which is not engaging itself. And, if the door latch will not engage the dishwasher will sense it as open door and will not start the cycle. Check the door switch and door latch. However, the water is going in the unit so it seems to be a bad control panel which should be replaced. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Most dishwashers have a soil separator which separates the soil from the water while it's washing. When a wash cycle is over a valve opens in the separator to allow the soil to go down the drain. If it's not working properly the washer will leave a film or food particles on the dishes.

Here are your diagrams and parts. I noticed a filter and trap which could be your problem. Make sure the water is spraying out the spray arms good.

http://www.appliancepartspros.com/partsearch/model.aspx?model_id=20680&diagram_id=676283#d676283

Check and fill the rinse aid compartment.

Hi


Thanks for using FixYa. Please check for the following--

1. Wire fasteners at dishwasher junction box.
2. Electronic control board faulty.
3. Motor (inoperative, check resistances).
4. Door switch (open contacts).
5. Door latch not making contact with door switch.
6. Touch pad circuit defective.

Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Hi


Thanks for using FixYa. First of all please check the Water temperature by using a thermometer inside the dishwasher to measure the water temp. It should be as close to 125 degree F to 140 degree F as possible. Now try using the temperature boost feature if your dishwasher is equipped with this cycle feature and check if this will help your wash ability issues.

Now check the Powder soap by making sure that you store your soap in a dry environment and it is not stale and clumping together. Possibly try a different detergent like a liquid or gel. Also, make sure the dishes are loaded properly, or dishwasher is not overloaded.

To check the proper filling dishwasher will fill with water up to and around the heating element. If water is more below the heating element, you may have low water pressure or a problem with the fill valve. Try & listen if it sounds like it is spraying the water around with enough pressure.

For low water pressure, try to clean the screen at the entrance of the fill valve, sometimes the fill valve can fail and not allow the proper water into the dishwasher and may need to be replaced. And, check the spray arm and pump cover for splits or leaks. Also make sure that the water is draining and is not accumulated in the dishwasher, if it is in dishwasher then check for clogged drain hoses and drain pump.


Low water fills are a very common trouble maker with today's dishwasher. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Hi,
The two major reasons for no drainage in your dish washer is either Food & debris are blocking the drainage basket or Food is clogging the drain hose. Check out this article which would assist you do some steps to get it cleared.
http://household-tips.thefuntimesguide.com/2006/07/fix_dishwasher.php
Please accept the solution if this assisted you.
Thank You for contacting Fixya.com

CHECK TO SEE IF YOU HAVE POWER TO THE MACHINE. IF YOU DO REMOVE THE PANNEL AND CHECK THE DOOR SWICHES. IF THATS GOOD YOU PROBEBLY HAVE A BAD BOARD. If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

check for a kink in water supply usually by the intake at the unit also check water valve is wideopen also check if there is a screen filter at either end of supply sometimes its in the brass fiting

Hi


Thanks for using FixYa. Leaks from the door itself may be caused by a faulty door gasket or door tightness adjustment. You should check the main tub seal, the door latch, the door gasket, the water-inlet valve, and the fill and drain hoses.

Also make sure the dishwasher is sitting level (you can adjust the front feet up or down, and many units have some type of levelers at the rear). Water under the dishwasher may be originating from a leaky hose or loose hose connection. Remove the lower front panel, and check the hoses. The pump seal may be defective, too; replacing this is a job for an appliance repairperson. An older dishwasher may corrode at the bottom, but this is fairly uncommon. If this is the case with your dishwasher, it's time for a new one.


Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101

][\[

bearings are possibly going out on the motor. If the sound is like metal grinding on metal then that's the problem. To repair it you will need to remove the dishwasher from under the cabinet and flip it upside down to access the motor assembly. Take the model # and serial # to an appliance part supply for proper motor replacement. It isn't hard to do if you have the time. Make sure the unit is unplugged and the water line has been disconnected before any repairs start.

Hope this helped you

Dave

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101

';';

make sure you didnt kink the water hose,wires on tight.check the float inside the dishwasher .it should lift up and down freely if its stuck up (maybe something is under it) it wont let it fill.good luck!
ERIC If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

Hi


Thanks for using FixYa. Please check for the following if your dishwasher is not working--


1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection faulty. Repair or replace wire fasteners at dishwasher junction box.
3. Electronic control board faulty.
4. Motor (inoperative, check resistances).
5. Door switch (open contacts).
6. Door latch not making contact with door switch.
7. Touch pad circuit defective.
8. No indicator lamps illuminate when START or OPTIONS is depressed.


Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Hi


Thanks for using FixYa. If your dishwasher seems noisy, check these:


Water-inlet valve
An aging water-inlet valve can sometimes fail slowly, rather than all at once. It can shudder on and off rapidly, causing the incoming water lines to shake, rumble, and rattle--sometimes violently. If yours is doing this, replace the inlet valve.
Motor
If it's the motor that's noisy, either of these may be the "culprit:"
As motor bearings wear out, they can become quite loud when the motor runs. They wear out quickly if they frequently get wet, because the water washes away the motor bearing grease. Bearings can get wet if the spin seal is defective. Then there will also be water leaking onto the floor beneath the dishwasher. Replace the seal if it leaks (read about the main tub seal in the "It leaks" section, later).
If, from beneath the dishwasher, you can see a round, plastic disc that's mounted to the top of the motor (a "slinger"), it may have broken free of the motor shaft. If so, it could be rattling around the shaft while the motor is running. If that's the problem, you need to replace the motor.
Heater fan
If the heater fan bearings are rusted or worn, they may squeal, or scrape loudly during the drying cycle. If this is the problem, replace the fan motor. Alternatively, the fan blade may be loose. If so, you need to replace it.
Pump
Small fruit pits, toothpicks, and fragments of glass sometimes get stuck in the pump. When this happens, open the pump and remove the debris. The pump is usually mounted directly to the motor, and then attached to the bottom of the dishwasher.
To get to the pump, you usually need to remove the lower rack, the spray arms, and the spray arm support from the inside of your dishwasher. A dishwasher pump isn't obvious. Look for an impeller--a round, plastic fan blade-type device that spins around and pushes the water toward the drain. When you can see the drain impeller, you should be able to see the clogging debris.



Please do rate the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

You cannot resize the wood once it has swelled. You have 2 choices: 1, replace the countertop with something more steam resistant or,2 remove the swelled area and replace the wood with pine or oak glued into place with moisture resistant adhesive.
Eric

Hi

Thanks for using FixYa. Dishwasher not draining properly or not draining at all issues can arise due to different reasons. Usually, these issues are related to kinked hoses, knocked out disposer unit (if connected with the dishwasher drain hose) & clogged drain pump & filter.

Also note that dishwashers do not drain completely after a finished cycle and this is normal. Dishwashers are designed to leave some water in the unit to ensure that the heating element doesn’t overheat. If you suddenly begin to experience a large amount of water being retained in your dishwasher, you have a problem. Some of the most common reasons include that the drain hose isn’t working properly, the drain pump isn’t working correctly, or possibly there is a plumbing problem in your home’s drain lines.



First check whether the drain is not clogged or blocked and the line is not kinked. Check all the hoses for blockages & also clean the air gap. Has the disposer been replaced recently? If so, chances are the knockout is still in place. Simply remove the drain hose from the disposer, and knock out the plug. If the disposer has not been replaced, try removing the drain hose from the disposer and use a wet-dry vacuum (prepared for water, of course) to **** any water (and hopefully anything else) from the drain line. Then reconnect the hose, and test the unit. If you have checked the air gap and the drain hose and can’t locate the problem, then it is an issue with the drain pump of the dishwasher.

Please do rate the solution and revert for further assistance.


Thanks

Rylee

Sounds like you need a dishwasher water inlet valve. This part allows water to flow during the wash and rinse cycles. This part is electrical so unplug the appliance before attempting repair. Part cost about $25. It is located behind the bottom kick plate. Two screws and two slip on wire connectors and you are done.

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101