Amana Dishwashers - Page 7 - Recent Questions, Troubleshooting & Support
No ice just replaced the ice maker itself
did you check to make sure there is water going to the fridge? It's possible the waterline may be clogged at the saddle valve. does the ice maker cycle? make sure the plug is in correctly and all the way.
Dishwasher reset code
only turn off the breaker from your wall circuit, wait by about 45 seconds. and turn ON again.God bless you
7/6/2013 8:02:32 PM •
Amana...
•
Answered
on Jul 06, 2013
NOT DRYING WELL
Add more rinse aid and check the heater is working. The dishwasher uses steam to dry the dishes.
4/21/2013 11:43:56 AM •
Amana...
•
Answered
on Apr 21, 2013
My Amana sofsound dishwasher is not draining
Hello,
When
you open the washing machine lid and discover it full of water, it
means it didn't drain before the spin cycle.
You may be confronted with
a tub full of sopping wet clothes at an inconvenient time, but don't
panic and call a repairman.
Chances are the trouble is with the drain
hose or the pump and you can fix it yourself with just a few simple
tools.
Difficulty: Moderately Challenging
INSTRUCTION BELOW.
-
1
Look
at the drain hose to make sure it isn't kinked or clogged. If there is
a piece of clothing lodged in there, clear away the hose from the pump
and yank the clothing out.
-
2
Take
a look at the switch under the lid of the washing machine. If it
doesn't click when you press it, it may be broken and the washer may
stop during the drain cycle. Call a repairman to repair or replace the
switch.
-
3
Examine the clothes tub and the outer tub of the washer for anything that may be stuck in there.
-
4
Open
the main access panel of the washer and take out the large rubber hose
connecting the pump to the lower part of the outer tub.
-
5
Check
to see if there is a piece of clothing stuck in there. If so, use a
pair of needle-nose pliers to grab the clothing and pull it through the
port. If it is difficult to reach, you will need to take out the
agitator, the top part of the outer cylinder, and the interior tub to
grab it. Unless you have special skills and tools, you may want to call
a repairman.
-
6
Inspect
the pump for a clog or frozen pulley. To check if the pulley is broken
or frozen, take the pump out and attempt to turn it manually with your
hands. If it's stiff or appears frozen, install a new pump.
Thanks for visiting .
No power seen at controls.
We had the same problem less than a year after we got ours. After two visits from the repairman, and a better business bureau complaint, they finally told us that there was a small opening on the inside of the door that allowed steam to escape into the area where the main circuit board is housed, causing it to short out. Replacing the circuit board and running a bead of silicone along the gap solved the problem. Hope that helps some!
Amana ADB1200AWQ model dishwasher, built -in, bought replacement part for broken door lock handle. Any idea as to steps to replace it?
Just replace my door latch handle for the 4th time in 6 years. its very easy,,, you have the same as i do. latch and handle assembly i got from amana parts on the internet, # for part is W10130697. it is the same i think as a whirlpool part. call 877-827-5003 to order about 48 bucks. very easy to fix. Open dishwasher door and take out the tork screws ,you will see the latch with the 2 micro swithes on both sides, black on the right and white wires on the left. pull off the plugs , put the new door latch assembly in place and put the two plug bacl on micro switches, put back in all the tork scews and your set to go.... good luck... it is real easy.
Not finding what you are looking for?