Amana Logo

Amana Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 1K Products
  • 75K Answers
  • 2M Views

HOW WOULD WE GUESS . TRY IT AND FIND OUT FOR YOURSELF . THAT IS HOW WE ALL LEARN THINGS

Amana Microwave... | Answered 3 hours ago


Hello there and welcome to fixya
From what you're describing it sounds like the drain pump is blocked. The nd error code indicates "no drain". If the unit can't drain it won't spin. You're going to have to slide the washer out far enough to remove the rear panel; be careful not to damage the floor. Once you get the rear panel off you will see the pump. Be sure to have plenty of towels & a small container to catch water. I am sending you instructions from the service manual to remove and replace the pump. Another possibility is the drain line is blocked or something is stuck in the tub to pump hose.

Amana Washing... | Answered Yesterday


May be the relay on the compressor. Is it cooling properly?

Amana ABB1927DE... | Answered on Feb 18, 2019


You mean ALE643RBW... drew blanks when I first looked and gave up. So... there's no moister sensor for this model. It runs the cycle by the start point of the timer. Its labled "more" dry or "less" dry in some fashion which merely changes the length of the cycle. Simple and dependable but doesn't meet todays "green" requirements.
Most likely it is the timer which lists at ~$170US from Sears. Your dryer has gotta have some years on it so not sure what else it may need in the near future. If you can do repairs yourself, $80 refurb timer on Ebay Otherwise to pay labor and markup... better off with new.

Amana Dryers | Answered on Feb 17, 2019


What can I do if my machine doesn't work properly

Amana Washing... | Answered on Feb 12, 2019


Try disconnecting the power to see if it will reset. If that does not fix it, it will probably need a main board, but more testing needs to be done to know for sure.

Amana Kitchen... | Answered on Feb 12, 2019


Error code f6 is an incorrect voltage code. The first thing to do is go to the breaker box and shut the power off to the oven. In some cases there maybe more than 1 breaker controlling the oven, make sure all the power is removed for 5 minutes. After waiting the 5 minutes test the oven if it works all is good, if not you need to gain access to the main board and start checking powers in and out. A lot of the time on a good visual inspection of the wiring and main board you will find the problem due to a melted or burnt spot. I hope this helps.

Amana Ovens | Answered on Feb 12, 2019


LO or FL error is displayed if no water is entering the washer. Check to see if water valves are turned on and check in line filter screens at inlet to hoses. " https://www.6ya.com/callphilipforhelp

Amana Washing... | Answered on Feb 08, 2019


Once the bolt is removed, it should be able to just pull up. It may be tough but grab it from the base and pull up with some force. Carefull not to hit your face once you free it up.

Amana Washing... | Answered on Feb 07, 2019


How are you determining that one section.is cold and one warm? If this is in fact the case you have a blockage in the coil or a compressor that is down provided this is a multi compressor unit.

Amana Heating &... | Answered on Feb 06, 2019


I know this is late but I had to add a solution to this problem since I had the exact same problem and was able to solve it. The probelm is not your control board. On these units, the heat pump compressor will not kick in unless the temperature you set on the control panel is within 2-1/4 degrees (or 4 degrees depending on your unit model. Otherwise, the unit locks out the compressor until the electric heat coil bring the indoor temperature up to that level - and then will switch the compressor back on for heat pump operation. So the problem is not the control panel or the compressor, it the electric heat coil. The coil has two manual limit switches on it that may be tripped and should be checked. The coil can be easily accessed by shutting down the power, removing 4 screws around the air outlet, pushing the screen up and sliding the panel out the top. The power wires can remain in place while the limit switches are reset. Hope it works.

Amana... | Answered on Feb 03, 2019


I solved my problem by going someplace that wasn't going to charge me!

Amana AFD2535DES... | Answered on Feb 02, 2019


There should a on-off rocker switch on the icemaker. Turn it off.

Amana... | Answered on Feb 02, 2019


Assuming unit has cooled down, unplug for 5 minutes and then plug back in. If code still flashes and door doesn’t unlock, there’s a problem with latch associated parts, the control board, or wiring between the 2.

Amana Kitchen... | Answered on Jan 30, 2019


I'm leaning 2 directions, one is that your tstat is sensing your heatpump can not keep up with the load. Therefore bringing on heat strips or two, you have a cycles per hour limit set for compressor heating and your machine is cycling too often.

Amana Heating &... | Answered on Jan 27, 2019


Always check the breakers in your electrical breaker box in house first. I say this because it takes 2 for dryers one for coils and lights the other for motor and thermostats. Next check door switch by listening for contact click sound when you push the door closed if you hear it switch is good and most likely motor is bad.

Amana Dryers | Answered on Jan 23, 2019


F1 - Control Board Failure - Replace control board (ERC). F2 - Oven Temperature Too Hot - Replace oven temperature sensor. F3 / F4 - Shorted or Open OvenTemperature Sensor - Replace oven temperature sensor. F5 / F6 / F8 - Control Board Failure - Replace control board.

Amana Heating &... | Answered on Jan 20, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Amana Experts

Marvin
Marvin

Level 3 Expert

83959 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Cindy Wells

Level 3 Expert

5763 Answers

Are you an Amana Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...