Questions & Answers for: Powermatic leeson motor

Ad

Question about 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence & Rout-R-Lift 1660806K

1 Answer

...Leeson motor that has a start and run cap then the run cap may not be the correct on. If you have a start cap blowing out I suggest you check the centriifugal switch in the end of the motor. It may ...

Ad

Question about 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence & Rout-R-Lift 1660806K

2 Answers

My Powermatic 66 table saw won't start. Tried to turn on my Powermatic 66 table saw this morning. Blade moved one half inch as if trying to start. Tried reset button on motor, still nothing.  I ...

Ad

Question about 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence & Rout-R-Lift 1660806K

3 Answers

I have recently purchased used powermatic 66 Table I have recently purchased a used powermatic 66 Table Saw, with a 3 hp single phase motor. Inside the electric switch box there is a small dial gage, ...

Question about 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence & Rout-R-Lift 1660806K

2 Answers

I have a powermatic table saw, 7 years old with a 2 hp baldor motor and when i start it the motor hums but the blade just shakes back and forth. I can turn the blade by hand and rotate the motor fan ...

Question about 1660802K Model 66 Special Edition 10 Inch Left Tilt 3 Horsepower Cabinet Saw With 30 Inch Accu Fence, 1 Cast Iron Extension Wing, And Table Board, 230 Volt 1 Phase

1 Answer

My Powermatic 66 tablesaw has a 3 phase 230 Vac motor on it but I cannot tell if it is a 3 hp or 5 hp. All the tags are gone from the motor. Is there any way to tell from the serial number? 8666-1008.

Question about 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence & Rout-R-Lift 1660806K

1 Answer

The saw starts but ramps up slowly. Under load the blade slows down. Seems as though the motor is not getting enough power or there is an issue with the motor itself. Any suggestions? Before you go ...

Question about 66 10" 3 HP 1 Phase 230V Table Saw w/ 30" Accu-Fence & Rout-R-Lift 1660806K

1 Answer

how do i take apart an electric motor I need to rewire the electric motor to work on 110 volts usually there is a plate where the wires go into the motor and on the back of it is a wiring diagram for ...

Question about 1352001 3520B 20x35" Wood Turning Lathe

2 Answers

Motor stopped while turning. It does have power but will not run. Powermatic 1352001 3520B 20x35" Wood Turning Lathe. I was rough turning a chunk of Cherry and the motor suddenly stopped. It did ...

Question about 1352001 3520B 20x35" Wood Turning Lathe

1 Answer

Need help wiring a 5HP 1Phase motor on Powermatic 66 so I bought this saw thinking as mentioned by the seller that is was a 3phase 5HP saw with a burned out motor as I got it to the shop I quickly ...

powermatic66 single phase 3hp starter switch not working how do I as they say retrofit this switch This saw had a square d 230 volt single phase starter on it. It would hum at startup but worked for a

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Powermatic Saw Experts

80stech

Level 2 Expert

120 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2010 Answers

Robert L Kershaw

Level 2 Expert

72 Answers

Are you a Powermatic Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...