Question about 29 NW CB Radio
...CB in my work truck. It has been sitting in my garage for a while. And the last i knew it worked... but now, I can hear the speaker ''click'' when powering on, but, when I key up, the needle dosent ...
Question about 636L Noise Canceling Microphone Microphone
...CB radio cannot legally exceed 4 watts of transmitting power. You can add anetnnas in order to increas the "gain" to have the equivalent of much more transmit power. Microphones aren't measured in ...
...CB meter may not be accurate, to measure power level use an external watt meter. If output power level is correct, the meter on the front of the radio can be adjusted internally to read correctly. ...
Question about 29 WX NW ST 40-Channels Base CB Radio
...CB user is right beside me. If they move more then a car lenght away i can see the signal come in but no voice. Also my PA switch when switched on does not send power through the PA outlet You have a ...
cb has power but no squelch,can't recieve or transmit Begin with Volume knob 12 o'clock position Squelch knob full counter clockwise RF gain knob full clockwise Pa/CB switch to CB Mic plugged in ...
...Power supply?? Microphone?? May be that you have a short in your coax in back of radio. Try taking it loose and screw it back in. Try new coax. Turn up Mic gain knob or change microphone. Make sure ...
Question about D104M6B/4B Model D104 Amplified Power Microphone, Durable high impact molded black ABS Housing, Power CB 4 Pin Handheld Microphone, Frequency Response 100 to 10,000 Hz, Impedance 5000 Ohm max., Output Level -44 dB below 1 volt per microbar at 1 kHz i
How do you retrofit a 4 pin D104 to a 2 pin model? I really want instructions on how to convert a 4 pin D104 for use on the 2 pin HW101. A two pin does not use a Push To Talk circuit so one wire you ...
Question about D104M6B/4B Model D104 Amplified Power Microphone, Durable high impact molded black ABS Housing, Power CB 4 Pin Handheld Microphone, Frequency Response 100 to 10,000 Hz, Impedance 5000 Ohm max., Output Level -44 dB below 1 volt per microbar at 1 kHz i
cb radio powers up recieve needle moves but there is no sound from speaker. Microphone keys but no modulation. Can you tell me what might be the problem. Thank you. Tried external speaker not working.
Question about D104M6B/4B Model D104 Amplified Power Microphone, Durable high impact molded black ABS Housing, Power CB 4 Pin Handheld Microphone, Frequency Response 100 to 10,000 Hz, Impedance 5000 Ohm max., Output Level -44 dB below 1 volt per microbar at 1 kHz i
...CB radio and power source. White: Audio Output (MOD) - Connects to the microphone input pin on the CB radio. Blue: Receive (RX) - Connects to the receive pin on the CB radio. Again, this is a general ...
Question about D104M6B/4B Model D104 Amplified Power Microphone, Durable high impact molded black ABS Housing, Power CB 4 Pin Handheld Microphone, Frequency Response 100 to 10,000 Hz, Impedance 5000 Ohm max., Output Level -44 dB below 1 volt per microbar at 1 kHz i
...mic numbers and cb plug numbers. if audio on mic is 3 and cb is 4 put 3 on 4 pin check each wire. using power mic make sure red and black wire are on the right pin, can damage radio or mic or
Usually answered in minutes!
980 Questions
644 Questions
497 Questions
317 Questions
274 Questions
