4003-0s clock wont count does turn to show time or swicth on lights

Give this a try.....Timing is not as critical with this method...no stop watch needed. Just count in your head...one-one thousand, two-one thounsand, etc, or usestop watch. The most critical step is step #3....wait 10 sec, instead of 7.



1. Ignition "ON", count to 3.

2. Depress/Release pedal 5 times...hard and fast.

3. Count to 10 (not 7!) and fully depress pedal

4. Count to 12 (SES should be blinking), release pedal

5. Count to 10, depress pedal

6. Count to 10, release pedal.

7. Turn off ignition, then 81377951893%26mt_id%3D570%26mpre%3Dhttp%253A%252F%252Fwww.ebay.com%252Fitm%252Flike%252F181377951893%26mid%3D446528%26sdc_id%3D%7Bsdc_id%7D&DealName=12v%20Electric%20Push%20To%20Start%20Engine%20Ignition%20Button%20With%20Red%20Led%20Light%20Up&MerchantID=446528&HasLink=yes&category=0&AR=-1&NG=1&GR=1&ND=1&PN=1&RR=-1&ST=&MN=msnFeed&FPT=SDCF&NDS=1&NMS=1&NDP=1&MRS=&PD=0&brnId=2455&lnkId=8070676&Issdt=150102050536&IsFtr=0&IsSmart=0&dlprc=19.99&SKU=181377951893">start engine. Done!

I have also tried to look for a solution to this problem but to no success. I had to let the client go.
However if you still have that problem try the following:

• First make sure the clock reads Trip B
• Turn off the ignition and hold down the trip switch
• With the trip switch still pressed, turn on and count five(5) seconds and release.
• Immediately you release tap once( the timing light should be blinking). A number 15 should show on the clock
  
• Wait for the blinking to stop and start your car.

Let me know if it works

Sounds like ign tumbler or ign switch is bad? If it wont come out of park checkto make sure brake lights are working if no could be brake light swicth which controls the shift interlock which if not working will not allow the shifter to come out of park.

there A BRAKE SWICTH BEHIND THE BRAKE PEDAL SWICTH THE OUT AND SEE ,IT,S A BRAKE SENSOR

Operating functions:
To set the clock, press and hold the clock/timer button for three seconds. A clock icon will appear on the left side of the screen. Input the time using the numerical buttons and then click the clock/timer button to save the time.
To set the timer, press and release the clock/timer button so that the display shows all zeroes. Enter the desired time using the keypad. Press start/stop to start the countdown. The countdown may be paused by pressing the stop/start button and resumed by pressing the same button again.
When countdown is complete, timer will beep continuously for thirty seconds and display will flash. Timer will then beep every ten seconds for ten minutes until the stop/start button is pressed.
This timer will also time up to time activities. To start count up, press clear/memory so timer reads all zeroes. Press stop/start and a plus sign will appear on the right side of the screen as the timer begins counting up.

Pressing the red button advances the chime count by one. Continue to advanced the chime count until it matched the hour shown on the clock face.

Count the number of blinks of the standby light. It will bink a count, pause and do it again (Common counts are 2 -9) Give this count to a Sony service center and they can help you know what the issue is. (Probably the lamp)

yes there is a light control on that car either turn the light swicth counter clock wise or the is a separet roller switch on the dash . c/k your owners manual

• Disconnect the power for 30 seconds. After restoring power, do not set the clock.
• If your model has an ON/OFF clock display, you can choose not to have the time displayed. To choose this option, press the 0 pad for about three seconds. To Turn the display back on, press the 0 again.

Touch the clock pad. Enter in the correct time of day by touching the numbers in sequence. Touch the clock pad again.

Hi!
From your brief description there could be many reasons for your Bagger not starting, Mine(FLHR 98) had a coil issue once however is the switch on the Bars above the starter button set to run? also which way are you turning the ignition as anti clock just puts on the side lights, pop it one click clockwise and oil battery lights should illuminate.
Finally I hope the battery is fully charged?
Fixya'd?
If so press the Blue button,
Cheer's
Paul 'W'
Onyer~EDson(:0)~[><U.K.