Question about HP LaserJet CM1015 MFP All-In-One Printer

1 Answer

How can I perform an NVRAM initialization with my HP CM1015 MFP

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 304 Answers

NVRAM initialization
CAUTION NVRAM initialization will erase all network settings. Before performing NVRAM
initialization, print a Network Configuration page, which contains network-setting information.
NVRAM initialization performs the following actions:
? Resets all customer-accessible menu settings via control panel and software back to the factory
default settings
? Resets the language to the value set at the factory
? Resets the default media size to cold reset media size
? Resets the symbol set to PC-8
NOTE The following steps reset the same NVRAM locations that are reset using the
Restore Defaults option in the control panel Service menu. The following process should be
used if the MFP does not come to a Ready state and an NVRAM initialization is desired.
Use the following procedure to perform an NVRAM initialization.
1. Turn off the printer.
2. Press and hold the Right arrow and Cancel buttons simultaneously.
3. Turn on the printer.
4. When you see the message Permanent storage init, release the Right arrow and Cancel buttons.
When the NVRAM init is complete, the printer returns to the Ready state.

Posted on Aug 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serial number need to be enterened KONICA C650


Notes:
1. When replacing the NVRAM or the EEPROM board, if the parts are replaced with used parts, the License Management error condition cannot be resolved by performing the repair operation.
In this scenario, Initialization would then be necessary and support must be contacted.
Additionally, if both the NVRAM and the EEPROM board are replaced, Initialization will be necessary.
IMPORTANT: Perform the Repair Procedure first, then the Initialize procedure. If initialization is required, collect the following information before calling support:
  • If i-Option was ever licensed on the MFP and if the additional 512MB of memory was ever installed at any time
  • The firmware level prior to the machine being upgraded to version 88 (bizhub C353 and bizhub C650 series models only)
  • If the machine ever had firmware version 85 or 86
  • A history of recent NVRAM or EEPROM board replacement
  • Obtain a machine Management List and have it ready to attach to the ticket.
  • A screenshot of the message returned from the LMS if "Repair" was unsuccessful
  • A "Request Code" from the MFP and the S/N must be obtained in order to start the "Initialization" procedure (see attached "Obtain Request Code" and "Initialize")
2. Make sure to enter the MFP Serial Number, Repair Demand Code and the Request Code in uppercase letters when entering data in License Management Server online.
3. Version 88 firmware refers to the bizhub C353 and bizhub C650 series models. Other models have the correct firmware from factory.
4. To view a PDF, you may need to download a free copy of Adobe Reader®.

Aug 19, 2017 | Konica Office Equipment & Supplies

2 Answers

Cannot connect to network. It show IP address 0.0.0.0


contact your service provide for assistance on how to set it up

Apr 28, 2015 | HP LaserJet P2015n Printer

1 Answer

Initializing scanner please wait


Reset the NVRAM should fix the problem. Get the NVRAM reset procedures from HP support site or Google them. Regards, Mike

Apr 03, 2014 | HP LaserJet 4730 MFP Printer

2 Answers

Printer does not reset


HP tech support might help you in this matter you can reach them directly on this number (877-690-9305) or just follow the link Support For Hp Printer

Apr 18, 2013 | HP LaserJet 1200 Printer

1 Answer

Cold reset for hp cm6040


Please follow
-------------------------------------
To perform an NVRAM initialization
1. Turn the product off and then on.
2. When the memory count appears on the control-panel display, press and hold 3 until all three LEDs
flash once and then stay on. This might take up to 20 seconds.
3. Press and release 9, and then press and release Start.
4. Press and release 6.

Hejazi

Mar 18, 2013 | HP Color LaserJet CM6040f MFP Q3939A...

1 Answer

Unable to uninstall CM1015 software


Hi
How about disconnecting the printer from power completely and restarting your PC?

Mar 24, 2012 | HP LaserJet CM1015 Photo Printer

2 Answers

CM 1015mfp Colors are not aligned. when printing the characters looks like 3D.


If nothing else works, you may have to manually calibrate the dials inside the mirror box. This video link will show you how. http://youtu.be/R1DIko0a1MA
This may be necessary if the printer got bumped really hard.

Aug 17, 2011 | HP Color LaserJet CM1015 Printer

1 Answer

Whenever I print my document, it doesn't exist the document I want to print but many strange symbols appear on the printed paper, how can I solve this problem?


Cold reset
A cold reset changes most system parameters in NVRAM to the factory defaults. However, unlike NVRAM inititialization, a cold reset does not reset the page count, the paper tray sizes, language, or formatter number.
Note If an HP Jetdirect card is installed, remove it before performing a cold reset. Otherwise, the procedure will also reset all the HP Jetdirect settings as well as the printer settings.
To perform a cold reset
1 Turn the printer off.
2 Press and hold down the GO button.
3 Turn the printer on, and continue to hold the GO button for at least 5 seconds, but not longer than 15 seconds. During this process, the Attention LED will turn on.
4 Release the GO button.
Note If both the Attention and the Ready LEDs turn on before you release the GO button, you must start the procedure again with step 1.
5 The printer's LEDs will begin cycling. The cold-reset process will
run until completion, and the printer will return to the ready state.

If not work, tris this

NVRAM initialization

CAUTION Only perform the following procedure if absolutely necessary.
Performing an NVRAM initialization resets some parameters that cannot be restored later.
NVRAM initialization sets all default variables stored in NVRAM back to factory default values or to a default ROM value, depending on the variable. It also performs a system reset.

NVRAM initialization resets the following:

  • all menu settings to factory default values
  • factory settings such as formatter number, page counts, and factory paper settings
To perform NVRAM initialization
1 Turn the printer off.
2 Press and hold down the GO button.
3 Turn the printer on, and continue to hold the GO button for at least 20 seconds. During this process, the GO button, Attention, and Ready LEDs will each turn on.
4 Release the GO button.
5 The printer LEDs will begin cycling. The NVRAM-unit process will run until the printer is in the ready state.

Jul 30, 2011 | HP LaserJet 1300 Printer

1 Answer

I have a printer it is modle is Hp LaserJet p4015n, when i start it give me this error: (49.00FF ERROR To continue turn off then on). when I turn off then on it give me agane this error. thanks for help,...


HP 4015 NVRAM & hardrive initialization

Solution
A hard disk initialization will erase and reformat the printer's hard disk. Perform hard disk initialization only if an error code displays on the control panel indicating a disk error. Always try initializing the hard disk before replacing it.

1. Turn the printer on. 
2. As the printer performs its power-on sequence, press and hold the Menu button until all three lights on the control panel are lit. 
3. Press the back arrow . The message INITIALIZE DISK displays on the control panel. 
4. Press OK. The printer initializes the hard disk and continues the power-on sequence.


CAUTION: Initializing NVRAM resets the serial number, the model number, the event log, the page counts, and the EIO card. Use the SERVICE menu to restore the serial number and page counts. You also need to reconfigure any computers that print to this printer to recognize the printer. Initialize NVRAM only when absolutely necessary. In most situations, use a cold reset to return printer to factory defaults but still retain the needed values in the SERVICE menu. 

 NVRAM initialization
Before initializing NVRAM, print a configuration page and a supplies status page to gather the service menu values

1. Turn the printer on and watch the control panel display. 
2. When the display shows the memory count, press and hold the down arrow until all three lights on the control panel are lit
3. Press the up arrow . 
4. Press Menu . The message SKIP DISK LOAD displays on the control panel. 
5. Press the up arrow until NVRAM INIT is highlighted, and then press OK. The printer initializes NVRAM and then continues its power-on sequence.

daca aceasta procedura nu reuseste, atunci va trebui sa inlocuiesti formatter-ul. daca nu exista hard disk

Good luck

Dec 12, 2009 | HP LaserJet P4015N Printer

1 Answer

My HP Laserjet colour CM1015 MFP printer does not pick up the paper. It doesnt calibrate either and I dont know why


I eliminated everything except two new non HP majenta and cyan cartridges. I removed the cyan cartridge and replaced it with an empty magenta cartridge, giving me 2 magenta cartridsges and althought it didnt printy, it staretd to pick up the paper so paper feed was working. I knew then that the cyan cartridge was faulty and changed it. All works now

Nov 02, 2009 | HP LaserJet CM1015 MFP All-In-One Printer

Not finding what you are looking for?
HP LaserJet CM1015 MFP All-In-One Printer Logo

3,374 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...