YThe colors in my picture have yellow/green color cast.

Set the camera's white balance to match the lighting. Most indoor lighting has a yellowish cast to it, while by default cameras are set for sunlight.

Each filter intensifies its color and darkens others, especially the color opposite on the color wheel. They're not of much use in color photography, unless you want weird color casts, but they come into their own in black&white photography.
For example, a red filter intensifies red and darkens blue. It can make a sky look almost black, making clouds pop out. Similarly it can darken foliage. A green filter on the other hand will brighten foliage.
If your camera can take black&white photos, try taking pictures of a red rose with green leaves with and without the filters. With one combination the rose and the leaves will be the same shade. With a red filter the rose will be bright against the dark leaves. With a green filter you'll get a dark rose with bright leaves.
With digital photography you can achieve the same effect in postprocessing, but some times its easier to get the result in camera.

How to Fix a TV When the Screen Is Green


A TV is calibrated by the factory to provide a "standard" picture that attempts to appeal to the vast number of buyers who take the set home. To adjust a TV picture that is too green, you must first enter the hidden "service menu" that technicians use. Adjusting the colors to remove the green cast will save you the cost that would otherwise be incurred from a TV technician coming to your home. No special tools are needed, nor any expertise in how the TV works.

Press the power button on the remote of a TV whose picture is too green in order to turn it on.

Press and hold down the "Menu" key until the manufacturer's logo appears on the screen. This could take up to a minute or more. Release the "Menu" key when the logo appears.

Immediately press the "9," "8," "7" and "6" keys in this order. Press the "Enter" button on the remote to enter the "Service Menu" screen.

Press the "Menu" button to go to the second of the two "Service Menu" screens. Press down on the "Down" arrow until you highlight "Color Calibration." Press the "Enter" button to enter the "Color Calibration" screen.

Select one of the color bars on the screen. Adjust the color by changing the values of the color bar by pressing left and right on the "left" and "right" arrows on the remote. Repeat this procedure with the other color bars as well. Stop adjusting the colors when the green cast is no longer present.

Press and hold the "Power" button on the remote to exit the "Service Menu" and save the adjustments you have made. Turn the TV off.

If you have a yellow cast to your photos, the problem might not be your printer. If you're using a digital camera, indoors under incandescent lighting without a flash your pictures will look yellow.
If this is the case, set your camera's White Balance to Incandescent lighting or use the flash. If all of your pictures, even those taken in daylight, look yellow you'll have to adjust the colors on your printer using the "toolbox" software that comes with it and back the yellow off. I've found that HP printers tend to have better color rendition than Canon.

this unit may have a resistor on the green crt-board that has increased in value. check ohms(resistance) on all crt boards and compare to one another. these will have color bands that inicate value of resistance. you do not need to know color code, just match colors of resistors on each board then measure. you could also have weak green tube. turning down the master screen control located on the fous/screen block can reduce grn. drive. to adjust proper drive for each so the grey scale is correct, turn color to tv all the way down then adjust screen controls on block for black & white picture. when color is turned all the way down, you should not have any green, red, or blue over cast on screen. mch

Whenever you have a color cast, like green or magenta or blue it is an ink cartridge problem. You are out of a needed color or a replacement cartridge is not correct manufactures color. This can happen easily using 3rd party ink.

Nah i didnt get into any trouble,, feel free to use us anytime!!! I'm happy the scanner worked if you need any more help you know how to find us..Next time that happens with the scanner try unplugging it restart the system and then plug it back in.. :)

Picture Menu
Picture Mode: Expert1
*Backlight: 16
*Contrast: 83
*Brightness: 53
Sharpness: 50
*Color: 55
*Tint: 0
Expert Control

• Fresh Contrast: Off
• Noise Reduction: Medium
• Gamma: Medium
• Black Level: Low
• Real Cinema: On
• TruMotion: Low
• Color Standard: HD (N/A w/HDMI)
• White Balance: Warm
• **Method: 10-Point IRE
  • 10 IRE
    • **Red: 1
    • **Green: 2
    • **Blue: -16
  • 20 IRE
    • **Red: -6
    • **Green: 0
    • **Blue: -7
  • 30 IRE
    • **Red: -5
    • **Green: 0
    • **Blue: -4
  • 40 IRE
    • **Red: -8
    • **Green: 0
    • **Blue: -4
  • 50 IRE
    • **Red: -4
    • **Green: 4
    • **Blue: -4
  • 60 IRE
    • **Red: -6
    • **Green: 6
    • **Blue: -5
  • 70 IRE
    • **Red: -8
    • **Green: 3
    • **Blue: -10
  • 80 IRE
    • **Red: -8
    • **Green: 7
    • **Blue: -16
  • 90 IRE
    • **Red: -9
    • **Green: 5
    • **Blue: -18
  • 100 IRE
    • **Red: -10
    • **Green: 4
    • **Blue: -9

Color Management System

• Red Color: 0
• Red Tint: 0
• Green Color: 0
• Green Tint: -15
• Blue Color: 0
• Blue Tint: 11
• Yellow Color: 15
• Yellow Tint: 2
• Cyan Color: -15
• Cyan Tint: 0
• Magenta Color: 0
• Magenta Tint: -1

lg70 nice tv excellent processor just to bad there is no intensity control on color management oh well still better than what the three s are pushing block out the hype lg will be number 1 in a few years haters are starting to come around and well leds coming,

p.s. i dont work for lg just tired of losers bashing stuff because they dont own it.
im isf certified those settings are right on the money straighter than a ruler

Use real color mode, saturation set to normal.

I know this contribution might be late, but try to avoid using the auto white balance. Use a tungsten mode and test each of its compensations until you get the desired result. I haven't had a similar problem on the 14n, but my D100 always places a magenta cast on white when shooting auto WB. I learned how to adapt the other WB modes to any situation.