At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Less than a week ago we installed our Frigidaire FRA256ST2 25000 BTU ThruWallWindow Air Conditioner
This morning it beeped and then shut off. NOTHING on the control panel will work but the green light is on on the cord
I have checked the breaker, checked the filter, clicked the test and reset button on the cord, tried the controls and the remote controller but nothing will make it come back on.... Any suggestions?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I understand you are looking for the manual to your Frigidaire air conditioner, model# FAC084N7A. I also see you want to know the BTU rating. Your air conditioner is rated 800-BTU. I have attached the manual below. Hope this is helpful.
I understand your Frigidaire air conditioner, model# LRA067AT7, will not turn on. I also see that the wall outlet is good, so you are wondering if there is an automatic shut off if the filter has not been cleaned. Your air conditioner does not have an automatic shut off, if the filter has not been cleaned. Please start by cleaning the filter. You can do this easily with the following instructions:
The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils.
1)Push the vent handle to the Vent Closed position (where applicable).
2)Open the front panel.
3)Grasp the filter by the center and pull up and out.
4)Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing
5)Or instead of washing, you may vacuum the filter clean.
Also, be sure your air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. Do not run your air conditioner without outside protective cover in place. This could result in mechanical damage within your air conditioner. Do not use an extension cord or an adapter plug.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
1)Plug in your Air Conditioner.
2)The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out.
3)Press the RESET button. Again you will notice a click as the button engages.
4)The power supply cord is now supplying electricity to the unit. 4)
I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
I understand that your Frigidaire air conditioner, model# FRA124HT2, begins with a constant beeping, and changes the modes itself, about every 30 minutes. I also see that it ends up on a different setting each time it does this. I suggest resetting your air conditioning, by either unplugging it or shutting the power off at your home's circuit breaker for 3-5 minutes. Bring power back to it and turn it on. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful.
Hello Naomi - Thank you for your question. When the air conditioner is beeping, it may be
a warning sign that the filter needs to be clean or that you need to reset the
unit. The LED (light) will illuminate and beep after 250 hours of operation.
After cleaning the filter, you may reset the "FILTER RESET" option by simply
pressing and holding down the button for approximately twenty seconds and the
light/beeping will go off. However, if you have done this, try pressing the "RESET"
button on the GFI plug of the unit. Wait approximately 2-3 minutes and then
turn on the air conditioner. If issue persists, then at this point I would
suggest reaching out to the manufacturer directly to see if you have any
limited warranty on the appliance or you may alternatively, visit the
manufacturer website for a comprehensive listing of appliance techs in your
area.
No sometimes the problem is intermint if it just three weeks old take it back for a new one. Dont wast your time for a service call, its cheaper ti repace.
×