I have a 3054. About 3 days ago it reset to 1-1-2005 and has never changed. it now reads 1-3-2005 at 5:57 PM

probably because you have it set to 12 pm midnight and not 12 noon so at 12 noon it is actually midnight when the date will change
reset the time of the day to am or pm and any pm settings will change the date at 12 midnight.

Hi.
I take it that your watch changes date at 12 noon, instead of 12 midnight.
If so change the time of your watch 12 hours, so it reads the same time, but instead of am, it is pm, or visa versa. Analog watches do not have a 24 hour time setting.

To set the time and date (must be done in this order) 1. Press MODE 3 times, then press START to change the seconds. 2. Press RESET to change the minutes, then press START until you get to the right minute. 3. Press RESET to change the hour, then press START until you get to the right hour. Note: If it says "H" on the right circle, it should read 24HOURS, otherwise it should read "A" for AM and "P" for PM. 4. Press RESET to set the date, then press START until you get to the right date 5. Press RESET to set the month, then press START until you get to the right number. 6. Press RESET to change the day of the week, then press START untilyou get to the right day. 6. Press MODE when done. Hope this helps

Welcome to FixYa!
Here's your request.
TIME AND DATE 1. Press and hold MODE until HOURS digits flash (you'll be in Alarm Mode) Press MODE again to enter TIME mode, SECONDS digits will flash. 2. Press ADJUST to set SECONDS to zero. 3. Press START/STOP to select MINUTES. 4. Press ADJUST to change. 5. Repeat to set HOURS, MONTH, DAYS, and DAY of WEEK. Go through 12 hours to set AM or PM. 6. Press MODE when done. 7. To display DATE from Time display , press START/STOP. 8. With DATE displayed press and hold START/STOP, then press ADJUST to change display between DATE-MONTH and MONTH-DATE. 9. With TIME displayed, press and hold ADJUST, then press MODE to switch between 12-and 24-hour format.
ALARM AND HOURLY CHIME 1. Press and hold MODE until HOURS digits, DAY, and A or P (for AM or PM) flash. 2. Press ADJUST to change HOURS digits. Go through 12 hours for AM or PM. 3. Press START/STOP to select MINUTES. 4. Press ADJUST to change.. Press MODE when done. 5. Press and hold ADJUST, then press START/STOP to turn chime on/off. Press START/STOP again to turn alarm on /off. Release START/STOP when done.
CHRONOGRAPH 1. Chronograph will count up to 24 hours. Lap times are not stored. After 40 minutes chrono display changes from seconds to minutes. 2. With time displayed, press MODE to select Chrono Mode. 3. Press START/STOP to start. 4. Press ADJUST to view lap time. Press again to sesume lap timing. 5. Press START/STOP to stop timing . Press ADJUST to reset chrono to zero. 6. Repeat for successive laps.
Thank you for using FixYa! Have a great day.
Jas247

My Wave Ceptor also reset to 01/01/05 four days ago. I've had it for more than a year and this is the first time it's happened. It hasn't reset with automatic updates and I can't get it to manually update.

Your watch thinks your noon is midnight.

Wind the hands forward 12 hours and the date change will be at midnight. You will have to re-set the date if it gains a day when doing this.

I tried putting your module number in (3054) and was able to download the instructions.

Try the following link http://ftp.casio.co.jp/pub/world_manual/wat/en/qw3054.pdf . This was successful in finding the manual you require.

Good luck and a happy new year.

When your winding the month over prop it so that its not quite all the way turned around or just turned around this works for me. Hope it works.

Press & hold set button the seconds will flash.

Press split/reset to set seconds to zero

Press mode to select hours

Press split reset to advance hour digits go through 12 hours to get to AM/PM

Press mode to select minutes


Press split reset to advance minutes

Keep repeatin the above steps to set month date day and 12/24 hour diplay

Press set when done.

The Skagen watches have  two-step stem; fully pulled out will change the time and partially pulled out will change the date (only goes one way so try turning it counter-clockwise or clockwise - I forget which is correct).  It's easier to find the date length by extending it all the way and then go back toward the case.  It won't change the date if you run it through a 24-hour cycle - you have to do the half-way thing.  Hope this helps.