Nordictrack A2050 Treadmill: we moved it back about 3 ft and tried to start it again. all it will do is walk on 1 or 7. nothing else. not even the fan will come on. any help will be appreciated. Thanks, Kim

there 3 things that you observe:
1) The walking belt is too Tight, the deflection will be 2-3" when you lift with his finger.Adjust the https://www.youtube.com/watch?v=XyPedy7HtzM
2) the thermic swithc of the motor Tripp for the tension of walking belt.

3)the driving belt of belt motor too tight. Deflection will be 1/8" loose the bolts of motor, and adjust.
Blessing.
[email protected]
whatsApp:+50588611441

The Controls Are Not Working on a NordicTrack Treadmill ...

www.livestrong.com > Sports and Fitness

Jun 1, 2015 - The Controls Are Not Working on a NordicTrack Treadmill ... Many glitches involving the controls on the console can be solved relatively quickly with some simple .... How to Use the iFit Videos with My NordicTrack Treadmil...

Nordictrack commercial 1750 that Icon can NOT fix - YouTube

? 3:52
https://www.youtube.com/watch?v=ILBbzyUXn2Q
Dec 16, 2011 - Uploaded by gerg6060
Nordictrack commercial 1750 that Icon can NOT fix ... I'll NEVER buy another Nordictrack again, Smooth or ...

[PDF]View Manual in PDF Format - NordicTrack

https://service.nordictrack.com/.../pdfDownload.do?...1...

NordicTracktreadmill is not working properly. (See. TROUBLESHOOTING on ... COMMERCIAL 1750 treadmill. ... Console. Book Holder. Key/Clip. Power Switch. Walking Belt. Foot Rail. Power Cord ... Set the treadmill in a cleared area and remove all packing materials. Do not dispose of .... Each workout automatically controls the speed.

Hi Kathy, yikes....does this constantly go up then down then up then down? There are a couple possibilities, 1) the upper console has gone goofy and is sending odd signals to the MCB, or motor control board, or 2) more likely, the MCB has a fault(s) causing the constant lift/decline. There is usually a protection circuit which allows ONLY one direction at a time with all lift assemblies to ensure the Up and Down windings are not energized at the same time, which would cause large amounts of smoke and a torched lift system, so it is possible that the MCB could cause this behavior. You can contact jatinah electronics and ask them, they can usually test your MCB for the cost of sending it there and back, and if a problem is found, they will advise you with repair costs which are 75 for this style of unit anyway. If they find no trouble, it zips right back to you verified good, for the cost of the shipping and time to send it in. No hidden gotchya's or fee's. Good Luck!

see if you can remove the motor hood and look at the drive belt. it is a little belt from the motor to the front pulley to turn the walking belt. its either broke or fell off

1) test the receptacle wall, plug a desklamp for to see if work if is working go
2( testing the power cord for open or defective.
3) reset the machine
4) test the fuse for blown and replace
5) test the c.breaker for tripped and reset again.
6) test the key, the key is small magnet, you can test with your magnet refrigerator with atraction or repulse, if doesnot replace the magnet from home depot.
God bless you

1) test the outlet wall , put a desklamp and see if work, if work the problem will be in the machine,
2) test the fuse inside for blown and replace with the same capacity
3) reset the circuit breaker inside.
4) test the power cord for open or defective.
Try again, if the machine NOT work, the problem will be in the power supply see the block atached.
God bless you

Manual with troubleshooting guide
https://www.sportsmith.net/images/product_support%5CNordicTrack%5CNTL10850%20-%20NORDICTRACK%20A2050%20TREADMILL%5CNTL1085.0-214878.pdf

https://www.justanswer.com/fitness-equipment/3tp0k-nordictrack-a2050-treadmill-just-recently-won-t.html


https://www.youtube.com/watch?v=Lx9zhfXok2A
https://www.sportsmith.net/images/product_support%5CNordicTrack%5CNTL10850%20-%20NORDICTRACK%20A2050%20TREADMILL%5CNTL1085.0-214878.pdf

Will be Around US$650,00 Used If the equipment is in Excelente Condition Mechanical+Electrical +Electronic.

Sincerely.

PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt has shifted to the left, Start unit @ 1.0 mph using the hex key, turn the left idler roller bolt clockwise 1/2 of a turn to move belt to the right. Be careful not to overtighten the walking belt. If the walking belt has shifted to the right, turn the left idler roller bolt counterclockwise or clock wise 1/2 of a turn depends on the tension that will be on the belt take your time and walk on it to feel the belt underneath you Repeat until the walking belt is centered.