I have a Kenmore Elite Quiet Pak 2, HE3 with a model number of 110.45862400 It is giving an error code of F11. I took the front plate off looking for the code book, but it was not there, now I am at a lose on the code. The machine works through all the cycles but the clothes are still pretty wet, even after trying the extended spin. Please advise if you can help with this and also where I might get another code book. Thanks, Pat

SOURCE: F2 error code on my Kenmore Elite HE3 washer

Based upon your description, the drain pump has either failed or the pump filter has become clogged.
To check the pump, remove the bottom access panel. There you will find access to the pump clean-out.(Large,white screw cap) BE READY TO CATCH LOTS OF WATER. CAREFULLY AND S_L_O_W_L_Y unscrew the pump clean-out, catching and discarding the water. When the water flow finally stops, completely remove the clean-out filter. Inspect the clean-out filter, the drain hose from the tub as well as inside the pump impeller for any additional debris.

If you need further assistance, let me know
Regards,
reg501

SOURCE: kenmore elite quiet pak 4 ''suds'' error

if it is truly oversudsing cut back on detergent or go back to standard he detergents not totally convinced of concentrated detergents are best way to go..if not oversudsing remove bottom cover and clean out pump pump restrictions will sometimes generated suds code

SOURCE: F2 error code on my Kenmore Elite HE3 washer

Had this problem on our Kenmore machine.

This is what done.

1. Unplug the washer

2. Take of the toe panel in the front by removing the three screws.

3. Get a bunch of towels (I mean a bunch!!!)

4. The pump is in the center, and it has a plastic grip handle that one can unscrew to remove the filter. As you unscrew it, LOTS of water will come out. Be ready with the towels. A cookie sheet helps to collect the water too.

5. Clean the filter assembly.

6. If one wishes to check the inlet of the pump, remove the back panel, about 12 screws. (Note, the following works for replace the pump as well)

7. Remove the large bellow from the bottom of the tub that goets to inlet of the pump by removing the clamp

9. Lift up on the plastic cover that covers the wires that power the pump. There may be a small plastic catch that is lifted up as to allow the connector to become free.

8. Remove the Torx screw that holds that is the center just under the filter screen.

9. Pull the pump forward.

10. Unclamp the pump outlet hose.

11. Remove pump

12. Unclamp the large bellow on the pumps inlet and inspect for debris.

13. Clean pump and fitler w/o getting water on the pump.

14. Install in reverse order. Remember, it is much easire to put the inlet bellow and outlet hose on the pump before you put into the washer

SOURCE: keep getting f2 signal on

F2 and F02 error are one and the same. My daughter was doing a load of towels in my Kenmore Elite HE3t front loading machine, when I went back to put them in the dryer the washer had a load of water in it and an error reading of F02. Checked the manual Could not find anything wrong with the Drain Hose?
 
These are the possibilities for that error code at one web site:
 
Press PAUSE/CANCEL twice to clear the display.* Check the drain hose and make sure it is not plugged or kinked.
* Check the electrical connections at the pump and make sure the pump is running.
* Check the drain pump filter for foreign objects.
* If the above does not correct the problem, replace the pump.
F02 is long drain.
Just because it came up doesn't mean there's a problem, it simply means there was a failure during the cycle, if it returns on a regular basis, you have a problem.
F02 error could be caused by the over use of soap, you need to make sure your using 2 tablespoons of HE soap, 1/4 cap at the most.
Over sudsing, could cause the water pump to run longer, the pump is designed for 15 min duty cycle which means, 15 minutes on to 45 minutes off. The computer may sense too much soap, and continue to pump. HE soap will cure that, along with SUD error, possible F09 (overflow condition), you may also notice the timing is wrong, HE soap works well in these machines and F/l washer go hand in hand
if the F02 returns the remove the 3 torx screws from the bottom kick panel, and remove the kick panel, right there in the middle you will see a big round handle, turn it and then slide it out, have some towels ready, there will be some water in there, and check to see if you have any thing in there that will slow water flow, tooth picks and other "floating" items may jam the impeller.

SOURCE: F2 error code on my Kenmore Elite HE3 washer

Depending on how fritzed your drain pump is this may or may not work. I've been using HE detergent because it is supposed to cause fewer suds. However, apparently is causing more suds than needed. I need to use only a couple tablespoons? If your clothes are not dirty enough for the soap to grab onto then extra suds are the result. The repair guy said we had an excessive amount of suds in the system and this affects the sensor and causes the drain pump to run and run and run until it shuts off from overheating. This is why we get the F2 and/or suds error code. He said once a month run the machine on the hottest water cycle with a cup of bleach (no clothes). This will clear out any suds build-up and is cheaper than Afresh which works, too, (but smells cleaner than bleach). After sitting for a day our pump started working again (yay!) It also stopped making the horrible loud sound. So glad I do not have to replace the pump!! yet...(knock on wood!).