I get an HP error message on 2600n printer saying "57 Fan Error". Is it fixable?

You do not state which HP printer you have but the 57 errors all indicate a problem with one fan or another. For instance, on an M4345 the 57.01 error would indicate that the cooling fan for the DC controller is not working.Here is a list of 57 errors by model Hp Error Code 57 Service Errors Codes 57 Tech Support

54.06

Error message

54.06

Description

Color density sensor error

Action

1. Power cycle the printer.
2. Calibrate the printer. Click here to view the document "HP Color LaserJet 2600n - Calibrating the printer" available on the HP Web site at (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00314525).
3. Change the Print Density settings through the HP Toolbox. Click here to view the document " HP Color LaserJet 2600n Printer - Change Device Print Settings in HP Toolbox" available on the HP Web site at (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00310627).
4. If the problem continues, contact HP Customer Support Center for technical assistance athttp://www.hp.com/support/clj2600n or see the flyer that came in the printer box for additional contact information.

Replace the fan

57.x FAN FAILURE CALL SERVICE Control Panel Message 57.x FAN FAILURE CALL SERVICE Event Log Error Service Messages: 57.01.00 57.02.00 57.03.00 57.04.00 Required Action

1. A fan motor failure occurred. All fans are enabled to low speed operation at printer power-on. Fans will go into high-speed operation during the print cycle. All fans are disabled during PowerSave Mode.
   • x = 1: FM1 (Laser/Scanner Fan)
   • x = 2: FM2 (Power Supply Cooling Fan)
   • x = 3: FM3 (Formatter Fan)
   • x = 4: FM4 (Face Down Deliver Fan)
2. Cycle power. It the message continues, check and reseat cabling between the fan motor(s) and the DC Controller PCA.
   • Fan 1 J208
   • Fan 2 J216
   • Fan 3 J210
   • Fan 4 J225
3. Replace the faulty fan motor.

it is non replaceble part error in this error we hv to replace the engine control card / clean the fan it may b resolved ur problem.....................

Hi,


it's a Power Supply Fan error,it is on the right-hand side,and below.
Reseat connections to the specified fan and DC controller.
If the error persists, replace the specified fan.
If the error persists Replace the DC controller

Use the Figure and table below to properly identify the 57.X error and the corresponding fan that is causing the error message.

A fan failure was detected.Printer fan or Duplex fan.
1. Check the fan’s connector and make sure the fan is not blocked.
2. Replace the fan.

On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, etc).

57.x FAN FAILURE CALL SERVICE Control Panel Message 57.x FAN FAILURE CALL SERVICE Event Log Error Service Messages: 57.01.00 57.02.00 57.03.00 57.04.00 Required Action

1. A fan motor failure occurred. All fans are enabled to low speed operation at printer power-on. Fans will go into high-speed operation during the print cycle. All fans are disabled during PowerSave Mode.
   • x = 1: FM1 (Laser/Scanner Fan)
   • x = 2: FM2 (Power Supply Cooling Fan)
   • x = 3: FM3 (Formatter Fan)
   • x = 4: FM4 (Face Down Deliver Fan)
2. Cycle power. It the message continues, check and reseat cabling between the fan motor(s) and the DC Controller PCA.
   • Fan 1 J208
   • Fan 2 J216
   • Fan 3 J210
   • Fan 4 J225
3. Replace the faulty fan motor.

51.22 is a Magenta laser scanner error.
Try removing the magenta restarting the printer and reinstalling.
If that does not work you likely need a laser assm.
You might want to call a tech. to replace.

My HP Color Laserjet 2600n Printer is giving me error as

" 50.2 Fuser error " . then every time i have to reatart my printer.
please give me suggestion.

thanks and regards.

ajinmumbai